Combination Vehicles: Coupling and uncoupling — Part 6
Questions in this part include: “After the guard disk gap has been set, how is the adjustment screw setting held?” · “Before you lower a trailer onto a gooseneck hitch, what must you confirm about the ball?”
Independent educational site · not affiliated with any government agency or DMV
Ready? Test yourself
Answer to start, or tap Start below:
After the guard disk gap has been set, how is the adjustment screw setting held?
- Instant feedback with an explanation
- Every answer cites its source in the manual
- Your best score is saved on this device
- Keyboard: press 1 to 3 to answer and Enter for the next question
Questions are written in our own words from the CDL manual; they are not the real test's questions. With your state chosen, every answer gives its page in your state's CDL manual. Without a state, answers cite the CDL manual, national model as printed by New Jersey (July 2017).
All 17 questions in this practice test
Take the test above first, then use this list to study. Tap “Show answer” to see the correct answer and explanation.
Show the questions and answersHide the questions
-
After the guard disk gap has been set, how is the adjustment screw setting held?
- With a cotter pin
- With the counter nut
- With the safety lock screw
Show answer
Correct answer: With the counter nut
The counter nut is tightened to keep the adjustment screw from moving off its setting.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
On a drawbar coupling, what applies if the safety cover bar will not fit properly into its seat?
- Drive slowly to a repair shop
- The combination must not travel at all
- Driving is allowed only on quiet roads
Show answer
Correct answer: The combination must not travel at all
A cover bar that does not seat correctly means the coupling is not secure, so the rig must not be moved.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
What covers the part of the drawbar coupling ball that still shows after coupling?
- A metal guard welded to the drawbeam
- A rubber bellows cover fitted against the ball
- A steel cap bolted to the safety cover bar
Show answer
Correct answer: A rubber bellows cover fitted against the ball
A rubber bellows cover keeps dust off the exposed ball, with its edge fixed tightly onto the ball.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
How is the inside of the drawbar eye lubricated?
- By spraying oil over the outside of the ball
- Through the grease nipple
- By taking the eye off and wiping it with grease
Show answer
Correct answer: Through the grease nipple
Grease is pumped in through the nipple, so the inner cup of the eye gets lubricated without taking anything apart.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
What is the first thing to confirm when you begin to uncouple a drawbar trailer?
- The trailer brake is applied
- The tow vehicle's engine is shut off
- The trailer brake line is removed
Show answer
Correct answer: The trailer brake is applied
The first step of uncoupling a drawbar is to make sure the trailer brake is on.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
Early in uncoupling a drawbar, what do you do with the adjustment screw and its counter nut?
- Tighten them further
- Remove them and fit new ones
- Loosen them
Show answer
Correct answer: Loosen them
After the rubber cover is taken off, the adjustment screw and the counter nut are both loosened.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
The drawbeam is lifted and the coupling ball can be seen fully. How do you move the tow vehicle to pull away from the trailer?
- Forward, at normal speed
- Backward, very slowly
- Forward, very slowly
Show answer
Correct answer: Forward, very slowly
Once the ball is fully visible, the tow vehicle moves forward very slowly to clear the drawbar.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
After the tow vehicle has pulled clear of the trailer, what happens to the safety cover bar?
- It is left open until you hook up again
- It is removed and kept in the cab
- It is turned back into its housing
Show answer
Correct answer: It is turned back into its housing
Once the vehicle has moved away, the bar is turned back inward until it settles into its housing.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
At the end of uncoupling a drawbar, what do you do with the safety lock screw and its nut?
- Leave them off so the bar stays open
- Store them in the cab until the next trip
- Put the screw back in and tighten the nut
Show answer
Correct answer: Put the screw back in and tighten the nut
The last step is to fit the safety lock screw back and tighten its self-locking nut.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
Before you lower a trailer onto a gooseneck hitch, what must you confirm about the ball?
- It is clean and dry
- It is set to its lowest height
- It is properly lubricated
Show answer
Correct answer: It is properly lubricated
With the clamp latch open, check that the gooseneck ball has the proper lubrication.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
When you hook up a gooseneck trailer, where must the coupler be before you lower the trailer?
- Just in front of the ball
- Slightly to one side of the ball
- Straight above the ball
Show answer
Correct answer: Straight above the ball
The coupler goes directly over the ball. Then the trailer is lowered and the clamp is latched.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
Which statement about safety chains on a trailer hooked to a gooseneck hitch is correct?
- Only loaded trailers need them
- Only trailers without brakes need them
- Every trailer must have them
Show answer
Correct answer: Every trailer must have them
The law requires safety chains on all trailers, so you attach them when you couple.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
After you plug the trailer light wiring into the tow vehicle, what should you do?
- Test only the turn signals
- Test only the lights at the rear corners
- Test all the lights, brake lights included
Show answer
Correct answer: Test all the lights, brake lights included
Connecting the wiring is followed by a check of every light, including the brake lights.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
What is done with the trailer jacks as the last step of coupling a gooseneck hitch?
- They stay halfway down to share the weight
- They are left on the ground as a support
- They are lowered all the way and stowed
Show answer
Correct answer: They are lowered all the way and stowed
The jacks are fully lowered and stowed, so the trailer's weight rests on the tow vehicle.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
What is the first step when you uncouple a gooseneck hitch?
- Raise the trailer off the ball
- Take out the safety pin and clip
- Disconnect the trailer light wiring
Show answer
Correct answer: Take out the safety pin and clip
You begin by removing the safety pin and its clip. Then the handle is turned and the trailer is raised off the ball.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
After the trailer is raised off the ball of a gooseneck hitch, what happens to the coupler?
- You must reset it by hand
- It stays open until you close it again
- It goes back to load position alone
Show answer
Correct answer: It goes back to load position alone
Once the trailer is lifted clear, the coupler goes back to the load position by itself.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
What is the final step when uncoupling a gooseneck hitch?
- Hook up the safety chains again
- Put the safety pin and clip back in
- Lower the trailer jacks to the ground
Show answer
Correct answer: Put the safety pin and clip back in
The procedure ends by installing the safety pin and clip again.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)