Combination Vehicles: 20 Hardest Questions
Questions that need a second thought, picked for close numbers, exceptions and easy-to-confuse rules. Take your time.
Independent educational site · not affiliated with any government agency or DMV
Ready? Test yourself
Answer to start, or tap Start below:
When you prepare to couple, how should the fifth wheel be tilted?
- Instant feedback with an explanation
- Every answer cites its source in the manual
- Your best score is saved on this device
- Keyboard: press 1 to 3 to answer and Enter for the next question
Questions are written in our own words from the CDL manual; they are not the real test's questions. With your state chosen, every answer gives its page in your state's CDL manual. Without a state, answers cite the CDL manual, national model as printed by New Jersey (July 2017).
All 20 questions in this practice test
Take the test above first, then use this list to study. Tap “Show answer” to see the correct answer and explanation.
Show the questions and answersHide the questions
-
When you prepare to couple, how should the fifth wheel be tilted?
- Up toward the cab of the tractor
- Down toward the rear of the tractor
- Level with the frame, with no tilt at all
Show answer
Correct answer: Down toward the rear of the tractor
A fifth wheel ready for coupling is tilted down toward the rear of the tractor.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
How does a bobtail tractor's stopping distance compare with a tractor-semitrailer loaded to its maximum gross weight?
- The bobtail needs a longer distance
- The bobtail needs a shorter distance
- The bobtail needs the same distance
Show answer
Correct answer: The bobtail needs a longer distance
A tractor with no semitrailer is hard to stop smoothly and takes longer to stop than a fully loaded tractor-semitrailer.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
What does a trailer without spring brakes not have?
- A parking brake
- Any air tanks
- A service air-line
Show answer
Correct answer: A parking brake
These trailers have emergency brakes that work from tank air, but no parking brake, so chock the wheels when you park them.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
What should you check about the position of a sliding fifth wheel?
- That it sits far enough back for a level trailer
- That it is slid fully to the rear for every trip
- That it is not so far forward that parts hit in turns
Show answer
Correct answer: That it is not so far forward that parts hit in turns
A fifth wheel set too far forward can let the tractor frame strike the landing gear or the cab strike the trailer when turning.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
When you pull the tractor forward partly clear of the trailer, where do you stop?
- With the tractor completely free of the trailer
- With the fifth wheel just behind the kingpin
- With the tractor frame still under the trailer
Show answer
Correct answer: With the tractor frame still under the trailer
Stopping with the frame under the trailer catches the trailer if the landing gear sinks or collapses.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
If a turn cannot be finished within your lane, when should you swing wide?
- As you finish the turn
- Before you begin the turn
- Halfway through the turn
Show answer
Correct answer: As you finish the turn
Swinging wide at the end of the turn keeps the gap closed, while a wide swing before the turn lets other vehicles pass on the right.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
A trailer has no spring brakes. Why is the hand valve a bad way to hold it while parked?
- The air could leak out and free the brakes
- The valve would wear out the relay valves
- The valve would lock the wheels for good
Show answer
Correct answer: The air could leak out and free the brakes
Always use the parking brakes when parked, and chock the wheels if the trailer has no spring brakes.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
You open the rear line valves but hear no air from either line. What should you check?
- That dummy couplers are fitted on the glad hands
- That the landing gear is fully raised up
- That the trailer and dolly shut-off valves are open
Show answer
Correct answer: That the trailer and dolly shut-off valves are open
A closed shut-off valve in the middle of the rig blocks air. All the brakes need air all the way to the back.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
How do you use the gear ranges of the landing gear crank when raising it?
- Start in low range, then switch to high once free of weight
- Stay in low range until it is all the way up
- Start in high range, then switch to low once free of weight
Show answer
Correct answer: Start in low range, then switch to high once free of weight
Low range starts the lift under load. When the weight is off, high range raises it faster.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
Which rig can get stuck on a raised crossing because of where its landing gear is set?
- A single-axle tractor pulling a long trailer set up for a tandem
- A tandem-axle tractor pulling a short trailer with gear raised
- A bobtail tractor whose fifth wheel is slid far to the back
Show answer
Correct answer: A single-axle tractor pulling a long trailer set up for a tandem
When a long trailer's landing gear is set for a tandem-axle tractor and a single-axle tractor pulls it, the gear can catch on the crossing.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
When might a big service-line leak first show itself?
- When you start the engine
- When you apply the brakes
- When you push in the air supply knob
Show answer
Correct answer: When you apply the brakes
Pressing the brakes uses the air in the line, so the loss shows up quickly then and lowers tank pressure fast.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
What do you check before you pull out the trailer air supply control to test the trailer emergency brakes?
- That the trailer landing gear is cranked down firmly onto the ground
- That the trailer rolls freely once the air brake system is charged
- That the tractor protection valve has already closed itself
Show answer
Correct answer: That the trailer rolls freely once the air brake system is charged
First build up air in the trailer system and see that the trailer moves without drag. Only then stop and pull the control out to test.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
When do you set the tractor parking brakes while easing pressure on the jaws?
- While the tractor is still pushing against the kingpin
- After the tractor has rolled out from under the trailer
- Only once the fifth wheel is fully unlocked
Show answer
Correct answer: While the tractor is still pushing against the kingpin
Setting the brakes while the tractor pushes on the kingpin keeps the rig still with the jaws unloaded.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
What happens when the service and emergency air-lines are crossed?
- The spring brakes release but the service brakes lock
- The trailer brakes work as usual using service air
- No supply air reaches the tanks, so spring brakes stay on
Show answer
Correct answer: No supply air reaches the tanks, so spring brakes stay on
Supply air goes to the service line, so the trailer tanks are not charged and the spring brakes have no air to release them.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
Looking into the back of the fifth wheel, where should the jaws have closed?
- Around the glide plate on the trailer
- Around the head of the kingpin
- Around the shank of the kingpin
Show answer
Correct answer: Around the shank of the kingpin
The jaws must have closed around the kingpin shank. You check this by going under the trailer and looking in.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
The trailer begins drifting off its path while you back. How do you correct it?
- Turn the top of the wheel away from the drift
- Turn the top of the wheel toward the drift
- Stop and pull the trailer hand valve
Show answer
Correct answer: Turn the top of the wheel toward the drift
Fix a drift at once: move the top of the wheel the same way the trailer is drifting.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
During the air flow check, how do you put air into the service line?
- Push the trailer air supply knob in
- Pump the tractor parking brake control
- Apply the trailer handbrake
Show answer
Correct answer: Apply the trailer handbrake
Applying the trailer handbrake, or pressing the service brake pedal, is what puts air into the service line for this check.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
What tells the relay valves how much pressure to send to the trailer brakes?
- Pressure in the emergency line
- The setting of the drain valves
- Pressure in the service line
Show answer
Correct answer: Pressure in the service line
The service line pressure is the signal, and the brake pedal or hand valve controls it.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
A rig has a rearward amplification of 2.0 in a quick lane change. What does that tell you?
- The rear trailer has double the tipping risk of the tractor
- The rear trailer is half as likely to tip as the tractor
- The rear trailer is four times as likely to tip as the tractor
Show answer
Correct answer: The rear trailer has double the tipping risk of the tractor
A rating of 2.0 means the rear trailer is two times more likely to turn over than the tractor.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
With the engine off, what should you hear as you apply and release the trailer brakes?
- A steady hiss both while applying and while releasing
- Air escaping when applied and the brakes moving when released
- The brakes moving when applied and air escaping when released
Show answer
Correct answer: The brakes moving when applied and air escaping when released
Applying the brakes should make them move, and releasing them should let air out.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)