Combination Vehicles: Coupling and uncoupling — Part 5
Questions in this part include: “What can happen if the pintle hook latch is not locked correctly?” · “Which of these actions is the final step when uncoupling a pintle hook?”
Independent educational site · not affiliated with any government agency or DMV
Ready? Test yourself
Answer to start, or tap Start below:
What can happen if the pintle hook latch is not locked correctly?
- Instant feedback with an explanation
- Every answer cites its source in the manual
- Your best score is saved on this device
- Keyboard: press 1 to 3 to answer and Enter for the next question
Questions are written in our own words from the CDL manual; they are not the real test's questions. With your state chosen, every answer gives its page in your state's CDL manual. Without a state, answers cite the CDL manual, national model as printed by New Jersey (July 2017).
All 17 questions in this practice test
Take the test above first, then use this list to study. Tap “Show answer” to see the correct answer and explanation.
Show the questions and answersHide the questions
-
What can happen if the pintle hook latch is not locked correctly?
- The trailer lights and brakes will stop working
- The drawbar eye can bind and be very hard to open later
- The trailer can separate, risking death or serious injury
Show answer
Correct answer: The trailer can separate, risking death or serious injury
A latch that is not properly locked can let the trailer come off the vehicle, which can kill or seriously injure people.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
At the start of uncoupling a pintle hook, where is the trailer parked and what is done to its tires?
- On firm ground with a slight downhill slope, tires blocked
- On a firm, level surface, with the tires blocked
- On a firm, level surface, with the tires left free to roll
Show answer
Correct answer: On a firm, level surface, with the tires blocked
The trailer is parked on firm, level ground and its tires are blocked.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
When uncoupling a pintle hook, what is done with the breakaway brake switch lanyard?
- It stays hooked up until the tow vehicle moves
- It is disconnected from the tow vehicle
- It is tied to the safety chains for the move
Show answer
Correct answer: It is disconnected from the tow vehicle
The lanyard is unhooked, together with the electrical connector and the safety chains, before the trailer is separated from the tow vehicle.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
What is done with the safety chains while uncoupling a pintle hook trailer?
- They are unhooked from the tow vehicle
- They are wrapped around the trailer tongue
- They stay attached until the jack is raised
Show answer
Correct answer: They are unhooked from the tow vehicle
The safety chains are taken off the tow vehicle along with the electrical connector and the breakaway switch lanyard.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
In the pintle hook uncoupling steps, what is done to the coupler before the jack is extended?
- It is left locked until the jack takes the weight
- It is unlocked and opened
- It is lifted above the tow vehicle hitch
Show answer
Correct answer: It is unlocked and opened
After the connectors, lanyard and safety chains are off, the coupler is unlocked and opened.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
What must the driver confirm about the ground before the trailer jack is extended?
- That it can hold the weight of the trailer tongue
- That it slopes slightly toward the tow vehicle
- That it is dry enough for the tires to grip
Show answer
Correct answer: That it can hold the weight of the trailer tongue
The jack pad will carry the tongue weight, so the surface under it has to be able to hold that load without sinking.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
What does turning the jack handle accomplish while uncoupling a pintle hook?
- It locks the coupler onto the hitch
- It moves the tongue weight onto the jack
- It releases the trailer brakes
Show answer
Correct answer: It moves the tongue weight onto the jack
Extending the jack makes it take over the load that the tow vehicle's hitch was carrying.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
Before the tow vehicle can leave, how far must the trailer coupler be raised?
- Until it clears the tow vehicle hitch
- Just level with the hitch
- Only until the hitch is unloaded
Show answer
Correct answer: Until it clears the tow vehicle hitch
The coupler must sit higher than the tow vehicle's hitch so nothing catches when the vehicle pulls away.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
Which of these actions is the final step when uncoupling a pintle hook?
- Driving the tow vehicle forward
- Disconnecting the safety chains
- Unlocking and opening the coupler
Show answer
Correct answer: Driving the tow vehicle forward
After the coupler has been raised above the hitch, the last step is to drive the tow vehicle forward.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
When coupling a drawbar, how far is the adjustment screw backed out at the first step?
- At most two turns
- At least five turns
- About three turns
Show answer
Correct answer: At least five turns
At the first step the adjustment screw is turned out at least five turns, before the safety cover bar is swung open.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
Before backing the truck toward a drawbar ball, where must the safety cover bar be?
- Swung inward and locked in its housing
- Swung outward until fully open
- Taken off the coupling altogether
Show answer
Correct answer: Swung outward until fully open
The cover bar has to be turned all the way out of the way so the drawbar eye can settle over the ball.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
Before you lift the trailer drawbeam off the coupling ball, what do you do with the safety cover bar?
- Swing it outward until it is fully open
- Leave it closed and tighten its screws
- Slide it along the drawbeam
Show answer
Correct answer: Swing it outward until it is fully open
The safety cover bar is turned outward until it is completely open, then the drawbeam is lifted off the ball.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
How is the truck reversed when lining up a drawbar coupling, and where does it stop?
- Very slowly, until the drawbar eye is exactly above the ball
- At a moderate pace, until the drawbar eye touches the ball
- Very slowly, until the drawbar eye is beside the ball
Show answer
Correct answer: Very slowly, until the drawbar eye is exactly above the ball
The truck creeps back so that the eye ends up directly over the coupling ball before the drawbeam is lowered.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
How far is the drawbeam lowered onto the coupling ball?
- Until the eye rests on the top edge of the ball
- Until the eye covers half of the ball
- Until the eye fully covers the ball
Show answer
Correct answer: Until the eye fully covers the ball
The drawbeam goes down until the drawbar eye surrounds the coupling ball completely.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
Once the drawbeam is down over the coupling ball, what is done with the safety cover bar?
- It is swung back in and fixed with the lock screw and nut
- It is left open so the ball stays in view
- It is turned back in and held only by the drawbeam weight
Show answer
Correct answer: It is swung back in and fixed with the lock screw and nut
The cover bar is turned back in over the ball and fastened with its safety lock screw and self-locking nut.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
What torque is used to tighten the two lock screws and their self-locking nuts on a drawbar coupling?
- 350 to 400 Nm
- 150 to 200 Nm
- 500 to 550 Nm
Show answer
Correct answer: 350 to 400 Nm
Both lock screws are tightened with a torque wrench set to 350 to 400 Nm.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)
-
What vertical gap is set between the guard disk and the ball cup with the adjustment screw?
- 1.0 to 1.5 mm
- 0.3 to 0.5 mm
- 3 to 5 mm
Show answer
Correct answer: 0.3 to 0.5 mm
The adjustment screw is turned until only a very small gap of 0.3 to 0.5 mm remains, and then it is locked with the counter nut.
Source: CDL manual, national model as printed by New Jersey, Section 6 (July 2017)