Driving Test Practice
English

Your stateNot chosenChoose it to see the page numbers of your state's own CDL manual.

Combination Vehicles: Driving combination vehicles safely

Rollover risks, steering and braking a combination, railroad crossings, trailer skids, wide turns and backing with a trailer. Split into 2 shorter tests so you're not stuck in one long quiz.

Independent educational site · not affiliated with any government agency or DMV

All 44 Driving combination vehicles safely questions with answers

Choose a part above to take a practice test, or study every question and answer here.

Show the questions and answersHide the questions
Part 122 questions
  1. What share of truck driver crash deaths comes from rollovers?

    • Less than a quarter
    • About one tenth
    • More than half
    Show answer

    Correct answer: More than half

    Rollovers cause over half of the crash deaths of truck drivers, which is why preventing them matters so much.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-001)

  2. What happens to a truck's center of gravity when more cargo is stacked up in it?

    • It shifts toward the rear axle and stays stable
    • It sinks lower and the truck grips the road better
    • It rises, so the truck tips over more easily
    Show answer

    Correct answer: It rises, so the truck tips over more easily

    Stacking cargo higher lifts the center of gravity away from the road. A truck with a high center of gravity rolls over more easily.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-002)

  3. Compared with an empty rig, how likely is a fully loaded rig to roll over in a crash?

    • Ten times as likely
    • Twice as likely
    • Three times as likely
    Show answer

    Correct answer: Ten times as likely

    Compared with an empty one, a loaded rig is ten times as prone to rolling in a crash.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-003)

  4. Which pair of habits best helps a driver prevent a rollover?

    • Keep the cargo low and take turns slowly
    • Keep the cargo high and take turns slowly
    • Keep the cargo low and take turns briskly
    Show answer

    Correct answer: Keep the cargo low and take turns slowly

    Low cargo keeps the center of gravity down, and a slow speed in turns keeps the rig from tipping.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-004)

  5. For which vehicles is keeping the cargo low even more important?

    • Combination vehicles rather than straight trucks
    • Straight trucks rather than combination vehicles
    • Both types of vehicle equally
    Show answer

    Correct answer: Combination vehicles rather than straight trucks

    Low cargo matters for every truck, but it matters even more for a combination vehicle than for a straight truck.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-005)

  6. Why is a load that sits to one side of the trailer a danger?

    • It lets the trailer lean, which makes a rollover more likely
    • It makes the tires wear on one side only
    • It moves the trailer's weight onto the tractor's steer axle
    Show answer

    Correct answer: It lets the trailer lean, which makes a rollover more likely

    A load pushed to one side makes the trailer lean. A leaning trailer is much closer to tipping over.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-006)

  7. How should cargo be placed on a rig to lower rollover risk?

    • Centered and spread out as widely as possible
    • Piled in a tight stack near the middle
    • Grouped on the side nearest the driver
    Show answer

    Correct answer: Centered and spread out as widely as possible

    A centered, spread-out load keeps the trailer from leaning, which lowers the risk of a rollover.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-007)

  8. When is a quick lane change especially risky for a combination vehicle?

    • When the rig is fully loaded
    • When the rig is empty and moving slowly
    • When the trailer is a short one
    Show answer

    Correct answer: When the rig is fully loaded

    Sudden lane changes should be avoided in any rig, and most of all when it is fully loaded.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-008)

  9. What can a quick lane change cause in a truck pulling a trailer?

    • A crack-the-whip effect that can tip the trailer
    • The tractor to lose its fifth wheel lock
    • The brakes on the trailer to release by themselves
    Show answer

    Correct answer: A crack-the-whip effect that can tip the trailer

    A sudden lane change can make the trailer whip sideways and overturn, even when the tractor stays upright.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-009)

  10. Which effect is behind the crack-the-whip movement of a trailer?

    • Rearward amplification
    • Trailer jackknife
    • Center of gravity height
    Show answer

    Correct answer: Rearward amplification

    Rearward amplification is the cause of the whip-like swing of a trailer. The greater it is, the more easily the rear trailer overturns.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-010)

  11. A rig has a rearward amplification of 2.0 in a quick lane change. What does that tell you?

    • The rear trailer has double the tipping risk of the tractor
    • The rear trailer is half as likely to tip as the tractor
    • The rear trailer is four times as likely to tip as the tractor
    Show answer

    Correct answer: The rear trailer has double the tipping risk of the tractor

    A rating of 2.0 means the rear trailer is two times more likely to turn over than the tractor.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-011)

  12. With triples, how much more easily can the last trailer roll over than a five-axle tractor?

    • 3.5 times as easily
    • 2 times as easily
    • 5 times as easily
    Show answer

    Correct answer: 3.5 times as easily

    With triples, the last trailer can be rolled 3.5 times more easily than a tractor with five axles.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-012)

  13. What is the minimum following distance for a combination vehicle going faster than 40 mph?

    • 1 second per 10 feet of vehicle length, with 1 extra second
    • 1 second per 20 feet of vehicle length, with 2 extra seconds
    • 1 second per 10 feet of vehicle length, with no extra time
    Show answer

    Correct answer: 1 second per 10 feet of vehicle length, with 1 extra second

    Allow one second for every 10 feet of vehicle length. Above 40 mph, add one more second.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-013)

  14. How does looking far down the road help a combination driver?

    • It avoids surprises that force a sudden lane change
    • It lets you drive closer behind other vehicles
    • It shortens the time needed to brake
    Show answer

    Correct answer: It avoids surprises that force a sudden lane change

    A far view lets you see trouble early, so you never have to swerve into another lane at the last moment.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-014)

  15. How fast should you drive a trailer rig at night?

    • Slow enough to spot obstacles in your headlights with time to react
    • Slow enough that the taillights ahead stay in view
    • At whatever speed keeps pace with the traffic around you
    Show answer

    Correct answer: Slow enough to spot obstacles in your headlights with time to react

    Your headlights must show you a hazard early enough for a gentle stop or lane change, so speed has to match what the lights reveal.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-015)

  16. When should you reduce speed for a turn in a rig pulling a trailer?

    The road ahead seen through a truck's windshield: a two-lane rural road that bends sharply to the right, with a yellow diamond curve sign and a 35 MPH plaque on the right before the bend.
    • Before you enter the turn
    • Partway through the turn
    • Just as you leave the turn
    Show answer

    Correct answer: Before you enter the turn

    Reach a safe speed before the turn begins, so you do not need to brake hard in the curve.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-016)

  17. How does the stopping distance of an empty large combination compare with a full one?

    • Longer for the empty one
    • The same, since the brakes are equally strong
    • Longer for the loaded one
    Show answer

    Correct answer: Longer for the empty one

    An empty combination needs more distance to stop than a loaded one.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-017)

  18. Why is a lightly loaded combination easy to lock up when braking?

    • Soft springs let the tires press into the road
    • Stiff springs and strong brakes give poor traction
    • Small loads overheat the brake drums at once
    Show answer

    Correct answer: Stiff springs and strong brakes give poor traction

    With little weight on them, the stiff springs and strong brakes leave the tires with poor grip, so the wheels lock easily.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-018)

  19. How does a bobtail tractor's stopping distance compare with a tractor-semitrailer loaded to its maximum gross weight?

    A tractor driving without any trailer on a level two-lane highway, its bare frame and fifth wheel showing behind the cab.
    • The bobtail needs a longer distance
    • The bobtail needs a shorter distance
    • The bobtail needs the same distance
    Show answer

    Correct answer: The bobtail needs a longer distance

    A tractor with no semitrailer is hard to stop smoothly and takes longer to stop than a fully loaded tractor-semitrailer.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-019)

  20. What lets a combination driver avoid a sudden panic stop?

    • Leaving a big gap and watching far ahead
    • Using the trailer hand valve more often
    • Staying in the right lane at all times
    Show answer

    Correct answer: Leaving a big gap and watching far ahead

    A long following distance and a long view ahead give you time to brake early and gently.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-020)

  21. Which of these can get stuck on a raised railroad crossing?

    • A possum-belly livestock trailer
    • A tanker trailer
    • A flatbed with its landing gear fully raised
    Show answer

    Correct answer: A possum-belly livestock trailer

    Low slung units, such as a lowboy, car carrier, moving van or possum-belly livestock trailer, can get stuck on a raised crossing.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-021)

  22. Which rig can get stuck on a raised crossing because of where its landing gear is set?

    • A single-axle tractor pulling a long trailer set up for a tandem
    • A tandem-axle tractor pulling a short trailer with gear raised
    • A bobtail tractor whose fifth wheel is slid far to the back
    Show answer

    Correct answer: A single-axle tractor pulling a long trailer set up for a tandem

    When a long trailer's landing gear is set for a tandem-axle tractor and a single-axle tractor pulls it, the gear can catch on the crossing.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-022)

Part 222 questions
  1. Your rig is stuck on a railroad crossing. What do you do first?

    • Stay in the cab and wait for help
    • Try to rock the rig free with the clutch
    • Leave the vehicle and move away from the tracks
    Show answer

    Correct answer: Leave the vehicle and move away from the tracks

    Leave the rig and move clear of the tracks, then phone 911 or another emergency number.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-023)

  2. Your rig is stuck on the tracks. Where can you find emergency notification information?

    • On signposts or signal housing at the crossing
    • On the railroad sign at the nearest station
    • In the shipping papers for your load
    Show answer

    Correct answer: On signposts or signal housing at the crossing

    Signposts or the signal housing at the crossing carry emergency notification details to use when you call.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-024)

  3. When you report a rig stuck on a crossing, which detail should you give if one is posted?

    • The weight of your cargo
    • The name of the railroad's owner
    • The DOT number of the crossing
    Show answer

    Correct answer: The DOT number of the crossing

    Call the emergency number and describe the crossing with landmarks, above all its DOT number when it is posted.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-025)

  4. In which condition is a trailer most likely to swing around when its wheels lock?

    Seen from above on a wet two-lane road: a tractor-trailer whose tractor is straight in its lane while the back of the trailer has swung out over the edge line onto the shoulder.
    • Empty or lightly loaded
    • Fully loaded to its gross weight
    • Loaded with its weight at the front
    Show answer

    Correct answer: Empty or lightly loaded

    Locked trailer wheels make it swing around, and an empty or lightly loaded trailer does this most.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-026)

  5. How can you first tell that your trailer is beginning to skid?

    • Feeling the steering wheel go light
    • Seeing the trailer in your mirrors
    • Hearing the trailer tires squeal
    Show answer

    Correct answer: Seeing the trailer in your mirrors

    Check your mirrors whenever you brake hard, so you can see the trailer swing out at once.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-027)

  6. Once a skidding trailer has swung out of your lane, what is the situation?

    Seen from above on a wet two-lane road: a tractor-trailer whose tractor is straight in its lane while the back of the trailer has swung out over the edge line onto the shoulder.
    • A jackknife is then very hard to prevent
    • The skid will correct itself by itself
    • Light braking will always straighten the rig
    Show answer

    Correct answer: A jackknife is then very hard to prevent

    After the trailer leaves your lane, stopping a jackknife is very difficult, so catch the skid early.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-028)

  7. Once you see the trailer skidding, what should you do with the brakes?

    Seen from above on a wet two-lane road: a tractor-trailer whose tractor is straight in its lane while the back of the trailer has swung out over the edge line onto the shoulder.
    • Press the brake pedal down harder
    • Let off the brakes to regain grip
    • Hold the brakes steady until it stops
    Show answer

    Correct answer: Let off the brakes to regain grip

    Letting off the brakes lets the wheels grip again, after which the trailer follows the tractor and straightens out.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-029)

  8. Why is the trailer hand brake the wrong tool for straightening out a skidding trailer?

    Seen from above on a wet two-lane road: a tractor-trailer whose tractor is straight in its lane while the back of the trailer has swung out over the edge line onto the shoulder.
    • It cuts the air supply to the tractor
    • It only works when the rig is parked
    • The trailer wheel brakes caused the skid
    Show answer

    Correct answer: The trailer wheel brakes caused the skid

    Braking the trailer wheels started the skid, so applying them again makes the skid worse.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-030)

  9. What name is given to the rear wheels following a different path than the front wheels in a corner?

    Seen from above at a city intersection: a tractor-trailer in the middle of a right turn, its tractor swung wide into the oncoming lane of the street it is entering while the trailer stays close to the curb, and an oncoming car stopped facing it.
    • Off-tracking
    • Rearward amplification
    • Jackknifing
    Show answer

    Correct answer: Off-tracking

    Off-tracking, also called cheating, is the way the rear wheels take a different path from the front wheels around a corner.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-031)

  10. In a rig with several trailers, which wheels off-track the most in a turn?

    • The rear wheels of the tractor
    • The front wheels of the first trailer
    • The rear wheels of the last trailer
    Show answer

    Correct answer: The rear wheels of the last trailer

    Each unit off-tracks more than the one ahead of it, so the last trailer's rear wheels cut in the farthest.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-032)

  11. Why do you steer the front of a long rig wide in a corner?

    Seen from above at a city intersection: a tractor-trailer in the middle of a right turn, its tractor swung wide into the oncoming lane of the street it is entering while the trailer stays close to the curb, and an oncoming car stopped facing it.
    • So the trailer wheels track exactly behind the tractor
    • So the rear end does not hit the curb or pedestrians
    • So the tractor stays well clear of oncoming traffic
    Show answer

    Correct answer: So the rear end does not hit the curb or pedestrians

    The rear wheels cut inside the front wheels, so the front must swing wide to keep the back off the curb and people.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-033)

  12. Why should the rear of your rig stay near the curb while you turn?

    Seen from above at a city intersection: a tractor-trailer in the middle of a right turn, its tractor swung wide into the oncoming lane of the street it is entering while the trailer stays close to the curb, and an oncoming car stopped facing it.
    • To keep the trailer tires from touching the curb
    • So that other vehicles cannot pass you on your right side
    • To let the tractor's mirrors clear the pavement
    Show answer

    Correct answer: So that other vehicles cannot pass you on your right side

    A gap beside the rear of the rig invites other vehicles to squeeze by on the right, so stay close to the curb.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-034)

  13. If a turn cannot be finished within your lane, when should you swing wide?

    • As you finish the turn
    • Before you begin the turn
    • Halfway through the turn
    Show answer

    Correct answer: As you finish the turn

    Swinging wide at the end of the turn keeps the gap closed, while a wide swing before the turn lets other vehicles pass on the right.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-035)

  14. To make the back of a trailer go left, which way do you first turn the top of the wheel?

    • To the left
    • Either way, then correct as it moves
    • To the right
    Show answer

    Correct answer: To the right

    Backing a trailer reverses the usual steering: you turn the wheel opposite to the direction you want the trailer to go.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-036)

  15. While backing a trailer, what do you do once the trailer begins to turn?

    • Steer the opposite way so the tractor follows it
    • Keep the wheel where it is until the end
    • Straighten the wheel and stop backing
    Show answer

    Correct answer: Steer the opposite way so the tractor follows it

    After the trailer begins to turn, steer the opposite way so the tractor follows the trailer.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-037)

  16. How should you position the vehicle before backing with a trailer?

    • Angled toward the passenger side
    • So the backing path is a straight line
    • Along a curved path whenever possible
    Show answer

    Correct answer: So the backing path is a straight line

    A straight-line path is easiest to control, so line the vehicle up before you start backing.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-038)

  17. If you have to back a trailer along a curve, which direction should the curve go?

    • Toward the passenger side
    • Whichever side has more room
    • Toward the driver's side
    Show answer

    Correct answer: Toward the driver's side

    Backing toward the driver's side lets you see where the trailer is going.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-039)

  18. What should you do before you begin backing a trailer?

    Seen from above: a tractor-trailer stands straight in a warehouse yard, some distance from an empty loading dock bay between two parked trailers, with a light pole and pallets near its path.
    • Check the path and walk around the vehicle
    • Rely on a quick look in the mirrors
    • Back a few feet to see what happens
    Show answer

    Correct answer: Check the path and walk around the vehicle

    Get out and walk the path first, checking the clearance at the sides and overhead.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-040)

  19. While you back a trailer, what should you do if you are unsure about your path?

    • Keep backing and check your left mirror only
    • Get out and look over the route once more
    • Sound the horn and keep backing slowly
    Show answer

    Correct answer: Get out and look over the route once more

    Use the mirrors on both sides often, and if you doubt your path, stop, get out and look again.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-041)

  20. Why should you back a trailer slowly?

    Seen from above: a tractor-trailer stands straight in a warehouse yard, some distance from an empty loading dock bay between two parked trailers, with a light pole and pallets near its path.
    • It keeps the air brakes from overheating on the way
    • It makes the trailer turn more sharply in reverse
    • It lets you fix your path before you go far off course
    Show answer

    Correct answer: It lets you fix your path before you go far off course

    A slow speed gives time to make corrections before the trailer drifts far off the path.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-042)

  21. The trailer begins drifting off its path while you back. How do you correct it?

    • Turn the top of the wheel away from the drift
    • Turn the top of the wheel toward the drift
    • Stop and pull the trailer hand valve
    Show answer

    Correct answer: Turn the top of the wheel toward the drift

    Fix a drift at once: move the top of the wheel the same way the trailer is drifting.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-043)

  22. If you cannot hold your line while backing a trailer, what can you do?

    • Keep going back until you reach the dock
    • Steer the same way as you would in a car
    • Pull forward to re-position the vehicle
    Show answer

    Correct answer: Pull forward to re-position the vehicle

    Pull-ups let you move forward and set up the vehicle again for a better line.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 6 (July 2017)⁩

    Report a problem with this question (cdl-cv-s6-044)