Driving Test Practice
English

Your stateNot chosenChoose it to see the page numbers of your state's own CDL manual.

Air Brakes: Using air brakes

Normal and emergency stops, braking with ABS, stopping distance and brake lag, brake fade, braking on downgrades, low air pressure and parking. Split into 3 shorter tests so you're not stuck in one long quiz.

Independent educational site · not affiliated with any government agency or DMV

All 48 Using air brakes questions with answers

Choose a part above to take a practice test, or study every question and answer here.

Show the questions and answersHide the questions
Part 116 questions
  1. You are making a normal stop in a truck with a manual transmission. When should you press the clutch in?

    A truck driver's footwell seen from the seat: three pedals, the wide brake pedal in the middle hinged at its base on a plate bolted to the floor; the driver's boot rests on the floor in front of it.
    • As soon as your foot touches the brake pedal
    • When the engine speed is down close to idle
    • When the truck has slowed to about half speed
    Show answer

    Correct answer: When the engine speed is down close to idle

    Keep the clutch engaged while the truck slows, and press it in only when engine rpm is down close to idle.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-156)

  2. After a normal stop is complete, what should you do with the transmission?

    • Shift to neutral and leave the engine running
    • Leave it in the gear you used for braking
    • Select a starting gear
    Show answer

    Correct answer: Select a starting gear

    Once the vehicle has stopped, select a starting gear so you are ready to move off.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-157)

  3. A vehicle has no ABS and you brake hard on a slippery road. What happens if the steering wheels lock up?

    • The vehicle turns more sharply than usual
    • The brakes release and you coast freely
    • You lose steering control
    Show answer

    Correct answer: You lose steering control

    Once the steering wheels lock, the driver can no longer steer the vehicle.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-158)

  4. Without ABS, what can happen when wheels other than the steering wheels lock up during hard braking?

    • The steering becomes lighter but the vehicle stays straight
    • The vehicle slows faster and stays in its lane
    • The vehicle may skid, jackknife, or spin
    Show answer

    Correct answer: The vehicle may skid, jackknife, or spin

    If wheels other than the steering wheels lock, the vehicle may skid, jackknife or even spin.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-159)

  5. What does the ABS computer do when it senses that wheels are about to lock up?

    • It cuts the brake pressure to a level that is safe
    • It raises the braking pressure to stop faster
    • It applies only the trailer brakes
    Show answer

    Correct answer: It cuts the brake pressure to a level that is safe

    ABS lowers the brake pressure so the wheels keep turning and you keep control.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-160)

  6. What can ABS help a driver do during hard braking?

    • Always stop in a shorter distance
    • Take downgrades at a higher speed
    • Steer around an obstacle while braking
    Show answer

    Correct answer: Steer around an obstacle while braking

    ABS may or may not shorten the stop, but it lets you steer around an obstacle and avoid skids caused by over braking.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-161)

  7. A combination vehicle has ABS on only one axle. How does that affect your control while braking?

    • It gives no help unless every axle has ABS
    • It makes the vehicle harder to steer
    • It gives you more control than no ABS at all
    Show answer

    Correct answer: It gives you more control than no ABS at all

    Even partial ABS, on one unit or a single axle, helps you control the vehicle when you brake.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-162)

  8. When only the tractor has ABS, what should you still be able to do?

    • Keep steering control, with less risk of a jackknife
    • Stop in a shorter distance on any road surface
    • Brake hard without watching the trailer at all
    Show answer

    Correct answer: Keep steering control, with less risk of a jackknife

    ABS on the tractor alone lets you keep steering, and a jackknife is less likely.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-163)

  9. Only the tractor has ABS. While you brake, the trailer starts to swing out. What should you do?

    Seen from above on a wet two-lane road: a tractor-trailer whose tractor is straight in its lane while the back of the trailer has swung out over the edge line onto the shoulder.
    • Brake harder to pull the trailer straight
    • Turn the steering wheel sharply the other way
    • Back off the brake pedal if that can be done safely
    Show answer

    Correct answer: Back off the brake pedal if that can be done safely

    Even with ABS on the tractor, ease off the brakes, if it is safe, when the trailer begins to swing out.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-164)

  10. What is a benefit when only the trailer of a combination has ABS?

    • The tractor can never jackknife
    • The trailer has less chance of swinging out
    • The tractor keeps full steering control in every stop
    Show answer

    Correct answer: The trailer has less chance of swinging out

    ABS on the trailer lowers the chance of it swinging out, but you must still ease off the brakes if the tractor starts to jackknife.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-165)

  11. Only the trailer has ABS. You lose steering control, or the tractor starts to jackknife. What should you do?

    Seen from above on a wet two-lane road: a tractor-trailer whose trailer is straight in its lane while the tractor has turned at an angle to it, its nose toward the shoulder.
    • Press the brake pedal harder to straighten the tractor
    • Pull the parking brake knob to slow the trailer first
    • Ease off the brakes, if it is safe, until you regain control
    Show answer

    Correct answer: Ease off the brakes, if it is safe, until you regain control

    Letting up on the brakes, when that is safe, lets you get control back.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-166)

  12. How should you brake a tractor-trailer combination that has ABS?

    • Use only the force needed to stop safely and keep control
    • Press harder than usual, since ABS prevents skids
    • Change your braking style depending on which unit has ABS
    Show answer

    Correct answer: Use only the force needed to stop safely and keep control

    Brake as you always have, with only the force you need, whether ABS is on the tractor, the trailer or both.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-167)

  13. In an emergency stop, who may press the brakes fully instead of using only the force needed?

    • A driver whose vehicle has ABS only on the trailer
    • Any driver of a vehicle that has ABS on at least one axle
    • A driver whose vehicles always have working ABS on every axle
    Show answer

    Correct answer: A driver whose vehicles always have working ABS on every axle

    Only a driver whose vehicle always has working ABS on every axle may brake fully in an emergency stop; everyone else uses only the force needed.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-168)

  14. The ABS on your vehicle stops working. What is the right way to handle it?

    • Drive as usual, and have the system serviced soon
    • Stop driving at once because no brakes will work
    • Pump the brake pedal constantly to replace ABS
    Show answer

    Correct answer: Drive as usual, and have the system serviced soon

    The regular brakes still work when ABS fails, so you can drive as usual and have the system serviced soon.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-169)

  15. Someone pulls out suddenly in front of you. When is hitting the brakes a good response?

    The road ahead seen through a truck's windshield: a two-lane road, and a red car that has pulled out from a side road on the right and stands across the truck's lane.
    • When you have room to stop and brake correctly
    • Only when the road is dry and the ABS lamp is off
    • Only after you have first tried to steer around
    Show answer

    Correct answer: When you have room to stop and brake correctly

    Braking is a good response when there is enough distance to stop and the brakes are used correctly.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-170)

  16. When you must stop in an emergency, how should you brake?

    The road ahead seen through a truck's windshield: a two-lane road, and a red car that has pulled out from a side road on the right and stands across the truck's lane.
    • Lock the wheels so the vehicle stops sooner
    • Rely mainly on the parking brake
    • Keep the vehicle straight and able to turn
    Show answer

    Correct answer: Keep the vehicle straight and able to turn

    Brake so the vehicle stays in a straight line and you can still steer if you have to.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-171)

Part 216 questions
  1. In the controlled braking method, how hard do you press the brakes?

    The road ahead seen through a truck's windshield: a two-lane road, and a red car that has pulled out from a side road on the right and stands across the truck's lane.
    • About half of full pedal travel
    • Lightly enough that the wheels never come near locking
    • Hard, but never so hard that the wheels lock
    Show answer

    Correct answer: Hard, but never so hard that the wheels lock

    Controlled braking means pressing as hard as possible while the wheels keep turning.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-172)

  2. During controlled braking, how much should you move the steering wheel?

    The road ahead seen through a truck's windshield: a two-lane road, and a red car that has pulled out from a side road on the right and stands across the truck's lane.
    • Very small movements only
    • Large movements to keep the vehicle straight
    • Full turns to steer around the obstacle while braking hard
    Show answer

    Correct answer: Very small movements only

    Keep steering movements very small while braking hard; if you need a bigger steering change or the wheels lock, release the brakes.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-173)

  3. In controlled braking, what do you do if the wheels lock?

    The road ahead seen through a truck's windshield: a two-lane road, and a red car that has pulled out from a side road on the right and stands across the truck's lane.
    • Hold the pedal down until the vehicle has stopped
    • Keep full pressure on and steer harder to recover
    • Release the brakes, then brake again as soon as you can
    Show answer

    Correct answer: Release the brakes, then brake again as soon as you can

    If the wheels lock, or you need a bigger steering change, let off the brakes and put them back on as soon as possible.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-174)

  4. In stab braking, you press the brakes all the way down. When do you release them?

    The road ahead seen through a truck's windshield on a divided highway: crates and a tarp-wrapped bundle lie across the right lane ahead, and a white car is in the left lane beside the truck.
    • As soon as the vehicle starts to slow
    • When the wheels lock up
    • When the low air pressure warning comes on
    Show answer

    Correct answer: When the wheels lock up

    Apply the brakes fully, release them when the wheels lock, then apply fully again once the wheels start rolling.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-175)

  5. In stab braking, what do you do once the wheels begin to roll again?

    The road ahead seen through a truck's windshield on a divided highway: crates and a tarp-wrapped bundle lie across the right lane ahead, and a white car is in the left lane beside the truck.
    • Put the brakes fully on again
    • Brake at about half pressure
    • Coast until the speed drops
    Show answer

    Correct answer: Put the brakes fully on again

    Once the wheels are rolling again, you apply the brakes all the way once more.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-176)

  6. In stab braking, after you let off the brakes, how long can the wheels take to begin rolling?

    • About a quarter of a second at most
    • Up to five seconds
    • Up to one second
    Show answer

    Correct answer: Up to one second

    The wheels may need up to one second to begin turning again once you let off.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-177)

  7. What happens in stab braking if you apply the brakes again before the wheels start rolling?

    The road ahead seen through a truck's windshield on a divided highway: crates and a tarp-wrapped bundle lie across the right lane ahead, and a white car is in the left lane beside the truck.
    • The brakes overheat and fade at once
    • The vehicle will not straighten out
    • The ABS malfunction lamp comes on
    Show answer

    Correct answer: The vehicle will not straighten out

    Braking again while the wheels are still locked keeps the vehicle sliding, so it does not straighten out.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-178)

  8. What is "brake lag" in a vehicle with air brakes?

    • The time air pressure needs to rebuild after a stop
    • The time the brakes need to work after the pedal is pushed
    • The time a driver needs to see a hazard and react
    Show answer

    Correct answer: The time the brakes need to work after the pedal is pushed

    Brake lag is the delay between pushing the brake pedal and the brakes actually working, because air must travel through the lines.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-179)

  9. With air brakes, how long can air take to reach the brakes through the lines?

    • One half second or more
    • Less than a tenth of a second
    • Five seconds or more
    Show answer

    Correct answer: One half second or more

    Air needs one half second or more to reach the brakes, while hydraulic brakes act instantly.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-180)

  10. Besides perception distance, reaction distance and braking distance, which distance is part of the total stopping distance of an air brake vehicle?

    • Skid distance
    • Following distance
    • Brake lag distance
    Show answer

    Correct answer: Brake lag distance

    Air brakes add brake lag distance to the other three parts of total stopping distance.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-181)

  11. At 55 mph on dry pavement, about how much distance does air brake lag add?

    • About 32 feet
    • About 16 feet
    • About 64 feet
    Show answer

    Correct answer: About 32 feet

    Brake lag adds about 32 feet at 55 mph on dry pavement.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-182)

  12. An average driver with good traction and good brakes goes 55 mph in an air brake vehicle. What is the total stopping distance?

    • More than 450 feet
    • About 250 feet
    • About 350 feet
    Show answer

    Correct answer: More than 450 feet

    Counting perception, reaction, brake lag and braking, the total is over 450 feet at 55 mph.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-183)

  13. What can cause brakes to fade or fail?

    A tractor-trailer coming down a long, steep mountain road, about to pass a yellow diamond warning sign that shows a truck on a slope.
    • Running the compressor with the tanks completely full
    • Heat from overusing the brakes and not using engine braking
    • Applying the parking brake while the truck rolls slowly
    Show answer

    Correct answer: Heat from overusing the brakes and not using engine braking

    Overusing the brakes and not using the engine to help slow down builds too much heat, which can make brakes fade or fail.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-184)

  14. During brake fade, what does excessive heat do to the brake lining?

    The two rear axles of a truck trailer stopped at the roadside: thin smoke rises from the wheels and a dull orange glow shows through the holes in the wheels.
    • It hardens the lining so that it grips better
    • It causes chemical changes that lower friction
    • It makes the lining swell against the drum
    Show answer

    Correct answer: It causes chemical changes that lower friction

    Too much heat changes the lining chemically, so it gives less friction.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-185)

  15. What happens to the brake shoes when overheated drums expand?

    The two rear axles of a truck trailer stopped at the roadside: thin smoke rises from the wheels and a dull orange glow shows through the holes in the wheels.
    • They reach the drums sooner and press harder
    • They stay where they are and the drums cool down
    • They travel farther and press on the drums less firmly
    Show answer

    Correct answer: They travel farther and press on the drums less firmly

    Expanded drums sit farther away, so the shoes have to travel more and press on the drum with less force.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-186)

  16. Why can brakes that are out of adjustment cause the other brakes to fade?

    • They take too much air from the other brakes
    • They do less work, so other brakes overheat
    • They lock first and slow the whole vehicle
    Show answer

    Correct answer: They do less work, so other brakes overheat

    Brakes that are out of adjustment do less work, so the remaining brakes carry more load and can overheat and fade.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-187)

Part 316 questions
  1. When can brakes get out of adjustment especially quickly?

    • When they are hot
    • When the air tanks are full
    • When they are cold
    Show answer

    Correct answer: When they are hot

    Hot brakes can slip out of adjustment quickly, so check the adjustment often.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-188)

  2. On a long, steep downgrade, what is the role of your brakes?

    A tractor-trailer coming down a long, steep mountain road, about to pass a yellow diamond warning sign that shows a truck on a slope.
    • They are the main control and the engine only helps
    • They only add to the slowing done by the engine
    • They replace the need for a low gear
    Show answer

    Correct answer: They only add to the slowing done by the engine

    The engine does the main work of holding your speed on a long or steep downgrade, and the brakes only add to it.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-189)

  3. On a long downgrade in the proper low gear, how hard should you apply the brakes?

    A tractor-trailer coming down a long, steep mountain road, about to pass a yellow diamond warning sign that shows a truck on a slope.
    • As hard as you can to stop quickly
    • Hard enough to feel a clear slowdown
    • Lightly enough that you barely notice them
    Show answer

    Correct answer: Hard enough to feel a clear slowdown

    Use enough pressure that you clearly feel the vehicle slow.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-190)

  4. You are braking on a downgrade. When should you release the brakes?

    • When you are about five mph below your safe speed
    • When you are about ten mph below your safe speed
    • When you have slowed to half your safe speed
    Show answer

    Correct answer: When you are about five mph below your safe speed

    Release the brakes once speed is about five mph below your safe speed.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-191)

  5. About how long should each brake application last on a downgrade?

    • About one second
    • About ten seconds
    • About three seconds
    Show answer

    Correct answer: About three seconds

    Each application should last about three seconds.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-192)

  6. Your safe speed on a downgrade is 40 mph and you released the brakes at 35 mph. When do you brake again?

    • When your speed is back up to 40 mph
    • Right away, and keep braking down to 25 mph
    • When your speed has climbed to 45 mph
    Show answer

    Correct answer: When your speed is back up to 40 mph

    Wait until the speed has risen back to your safe speed, then apply the brakes again.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-193)

  7. The low air pressure warning comes on while you are driving. What should you do?

    A truck's dashboard while driving on a two-lane highway: the speedometer needle is up, a red lamp marked LOW AIR is lit above the two air pressure gauges, and both needles are low.
    • Stop and park safely as soon as possible
    • Keep driving to the next shop and watch the gauge
    • Pump the brake pedal to rebuild pressure
    Show answer

    Correct answer: Stop and park safely as soon as possible

    Low pressure may mean an air leak, so stop and park safely while you still have air to use the foot brakes.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-194)

  8. When is controlled braking possible after the low air pressure warning has come on?

    A truck's dashboard while driving on a two-lane highway: the speedometer needle is up, a red lamp marked LOW AIR is lit above the two air pressure gauges, and both needles are low.
    • Only after the parking brake is applied
    • Only once the vehicle is below 20 mph
    • As long as the tanks still hold enough air
    Show answer

    Correct answer: As long as the tanks still hold enough air

    Controlled braking with the foot brakes works only while the tanks still hold enough air.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-195)

  9. Why does a heavily loaded vehicle take a long distance to stop when the spring brakes come on?

    • The spring brakes release as pressure drops
    • Spring brakes act on only some of the axles
    • The compressor shuts off the service brakes
    Show answer

    Correct answer: Spring brakes act on only some of the axles

    Spring brakes act on only some axles, so a heavy load takes a long way to stop.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-196)

  10. Which vehicle is at risk of skidding when the spring brakes apply?

    • A heavily loaded vehicle on a dry level road
    • Only a vehicle pulling a trailer
    • A lightly loaded vehicle, or one on a slippery road
    Show answer

    Correct answer: A lightly loaded vehicle, or one on a slippery road

    When the spring brakes apply, a lightly loaded vehicle or one on a slick road can skid and get out of control.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-197)

  11. On some older vehicles the parking brake control is a lever. How does it move?

    • It swings sideways, or up and down
    • It twists to the right, like a key
    • It slides in and out, like a drawer
    Show answer

    Correct answer: It swings sideways, or up and down

    On older vehicles the control may be a round blue knob or another shape, such as a lever that swings sideways or up and down.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-198)

  12. In which situation should you avoid applying the parking brakes?

    • The vehicle is fully loaded and on a gentle slope
    • The engine has just been shut off
    • The brakes are very hot from a steep downgrade
    Show answer

    Correct answer: The brakes are very hot from a steep downgrade

    Very hot brakes can be damaged by the heat if the parking brakes are applied, so let them cool first.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-199)

  13. What can happen if you use the parking brakes when the brakes are very wet and the weather is freezing?

    A tractor-trailer with its headlamps on, on a wet two-lane road in winter: slush along the road's edges, spray at the wheels, snow on the roadside and on the fir trees.
    • They can freeze and keep the vehicle from moving
    • The air tanks drain themselves and pressure drops
    • The spring brakes release by themselves
    Show answer

    Correct answer: They can freeze and keep the vehicle from moving

    Wet brakes can freeze in cold weather and keep the vehicle from moving.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-200)

  14. You cannot use the parking brakes because the brakes are too hot or wet in freezing weather. What should you use to hold the vehicle?

    • Leave the transmission in neutral with the engine running
    • Wheel chocks on a level surface
    • The service brake pedal held down
    Show answer

    Correct answer: Wheel chocks on a level surface

    Chock the wheels on a level surface instead of relying on the parking brakes.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-201)

  15. How can you dry out very wet brakes before parking in freezing weather?

    A tractor-trailer with its headlamps on, on a wet two-lane road in winter: slush along the road's edges, spray at the wheels, snow on the roadside and on the fir trees.
    • Press the pedal hard several times while stopped
    • Brake gently while driving in a low gear
    • Set the parking brakes and let the engine idle
    Show answer

    Correct answer: Brake gently while driving in a low gear

    Light braking in low gear warms the brakes and dries them.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-202)

  16. What must you do before you leave a vehicle unattended?

    • Apply the parking brakes or chock the wheels
    • Leave the engine running to keep air pressure up
    • Shift to neutral and release the clutch
    Show answer

    Correct answer: Apply the parking brakes or chock the wheels

    An unattended vehicle that is not held may roll away and cause injury and damage.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-203)