Driving Test Practice
English

Your stateNot chosenChoose it to see the page numbers of your state's own CDL manual.

Air Brakes: Cheat Sheet

The facts of this test you most need, grouped by topic, each with its page in the manual. Print it or keep it on your phone.

Independent educational site · not affiliated with any government agency or DMV

Driving Test Practiceofficialdrivingtest.com

100% free — no email, no paywall. Print it, save it, or share it with anyone studying for the same test.

Air brake system parts

  • Air brakes are made of a service brake system, a parking brake system and an emergency brake system.
  • The governor stops the compressor when tank pressure reaches the cut-out level, around 125 psi.
  • The cut-in pressure, around 100 psi, is the level at which pumping restarts.
  • Water in the air system can freeze when it is cold, and frozen water can make the brakes fail.
  • Tanks with manual drains must be drained by the driver once each driving day, at the end of the day.
  • Alcohol in the air system lowers the chance of ice forming, and ice can make the brakes stop working.
  • A safety valve usually opens at 150 psi.
  • Needless pedal use can drain the air faster than it is replaced, and if pressure gets too low the brakes will not work.

Gauges, warnings and dual air systems

  • The supply gauges report how much pressure is stored in the air tanks. A different gauge, not found on every vehicle, shows how hard you are applying the brakes.
  • Needing more and more application pressure to keep the same speed is a sign the brakes are fading from heat.
  • The low air pressure warning is normally a red light, and a buzzer may sound as well.
  • Large buses commonly signal low pressure at 80 to 85 psi.
  • Front brakes work well in every condition, and tests show front wheel skids are not likely even on ice.
  • A dual air brake has two separate systems, each with its own tanks, hoses and lines, but they work from one set of brake controls.
  • Wait until both the primary and secondary systems hold at least 100 psi before you drive.

Spring brakes, parking controls and ABS

  • Emergency and parking brakes must be held on mechanically, because air can slowly leak out. Springs do this job.
  • Air pressure pushes the springs back so the brakes stay released. When the air is removed, the springs apply the brakes.
  • Spring brakes apply fully when the pressure falls into about 20 to 45 psi, and typically 20 to 30 psi.
  • Newer air brake vehicles use a yellow, diamond-shaped push-pull knob for the parking brakes. Older vehicles may use a lever.
  • The spring force and the pedal's air pressure add together and can damage the brakes, so keep your foot off the pedal while the spring brakes are on.
  • For air brake trucks, buses, trailers and converter dollies, the ABS requirement starts with vehicles built on or after March 1, 1998.
  • ABS stays inactive during normal braking and acts only when a wheel is close to locking.

Inspecting air brakes

  • Movement of more than about one inch at the point where the push rod attaches means the brake is probably out of adjustment.
  • Brakes out of adjustment are the most common problem found at roadside inspections, so slack adjusters should always be checked.
  • Every vehicle built since 1994 has automatic slack adjusters.
  • Hand adjustment of an automatic adjuster is only a temporary emergency measure, because the brake will likely soon be out of adjustment again.
  • For a single vehicle, a drop of more than 3 psi in one minute with the foot brake applied is too much.
  • For a combination vehicle, a drop of more than 4 psi in one minute with the foot brake applied is too much.
  • Too much air loss means you could lose your brakes while driving, so the leaks must be found and fixed first.
  • In a dual system, pressure should climb to 100 psi from 85 in 45 seconds or less with the engine at operating rpms.

Using air brakes

  • Only a driver whose vehicle always has working ABS on every axle may brake fully in an emergency stop; everyone else uses only the force needed.
  • Controlled braking means pressing as hard as possible while the wheels keep turning.
  • Brake lag is the delay between pushing the brake pedal and the brakes actually working, because air must travel through the lines.
  • Brake lag adds about 32 feet at 55 mph on dry pavement.
  • Counting perception, reaction, brake lag and braking, the total is over 450 feet at 55 mph.
  • Overusing the brakes and not using the engine to help slow down builds too much heat, which can make brakes fade or fail.
  • The engine does the main work of holding your speed on a long or steep downgrade, and the brakes only add to it.
  • Release the brakes once speed is about five mph below your safe speed.
  • Low pressure may mean an air leak, so stop and park safely while you still have air to use the foot brakes.
  • Very hot brakes can be damaged by the heat if the parking brakes are applied, so let them cool first.