Driving Test Practice
English

Your stateNot chosenChoose it to see the page numbers of your state's own CDL manual.

Air Brakes: Inspecting air brakes

The engine compartment and walk-around checks, slack adjusters, and the final air brake check with its pressures and leak rates. Split into 2 shorter tests so you're not stuck in one long quiz.

Independent educational site · not affiliated with any government agency or DMV

All 42 Inspecting air brakes questions with answers

Choose a part above to take a practice test, or study every question and answer here.

Show the questions and answersHide the questions
Part 121 questions
  1. What do you check on a belt-driven air compressor during the engine compartment inspection?

    The front of an older truck engine: an air compressor driven by a belt from the engine's large pulley, with its air filter, a metal air line and a small valve unit beside it.
    • The compressor's intake filter and hoses
    • The governor's cut-out adjusting screw
    • The belt's condition and its tightness
    Show answer

    Correct answer: The belt's condition and its tightness

    On a belt-driven compressor you check how good the belt is and how tight it is.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-114)

  2. How should the vehicle be set up before you pull on the slack adjusters by hand?

    • On level ground, wheels chocked, parking brakes released
    • On level ground, wheels chocked, parking brakes applied
    • On level ground, wheels not chocked, parking brakes released
    Show answer

    Correct answer: On level ground, wheels chocked, parking brakes released

    The wheels are chocked so the vehicle cannot move, and the parking brakes are released so the slack adjusters are free to move.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-115)

  3. You pull hard on an S-cam slack adjuster. How much movement at the push rod means it probably needs adjusting?

    A driver in a hi-vis vest and work gloves kneels beside a trailer's wheels, which are chocked, and reaches in behind the tire with one arm; the round can of the brake chamber shows just past the tire.
    • More than about one inch
    • More than about two inches
    • More than about three inches
    Show answer

    Correct answer: More than about one inch

    Movement of more than about one inch at the point where the push rod attaches means the brake is probably out of adjustment.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-116)

  4. What can happen to a vehicle whose brakes have too much slack?

    A driver in a hi-vis vest and work gloves kneels beside a trailer's wheels, which are chocked, and reaches in behind the tire with one arm; the round can of the brake chamber shows just past the tire.
    • Its brakes release too slowly
    • It can be very hard to stop
    • Its compressor runs all the time
    Show answer

    Correct answer: It can be very hard to stop

    Brakes with too much slack are out of adjustment, and the vehicle can be very hard to stop.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-117)

  5. Which brake problem do roadside inspections find most often?

    • Cracked brake drums
    • Brakes out of adjustment
    • Air hoses cut by rubbing
    Show answer

    Correct answer: Brakes out of adjustment

    Brakes out of adjustment are the most common problem found at roadside inspections, so slack adjusters should always be checked.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-118)

  6. Vehicles built since which year all have automatic slack adjusters?

    • 1984
    • 2004
    • 1994
    Show answer

    Correct answer: 1994

    Every vehicle built since 1994 has automatic slack adjusters.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-119)

  7. A vehicle has self-adjusting slack adjusters. Do you still have to check them?

    Under a truck at an axle: a round air brake chamber, its push rod, and the slack adjuster arm it joins on the end of a shaft that runs into the brake behind the wheel.
    • No, they adjust themselves, so checking is skipped
    • Yes, they must still be checked
    • Only when you hear air leaking
    Show answer

    Correct answer: Yes, they must still be checked

    Even self-adjusting slack adjusters have to be checked. They adjust only during full brake applications.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-120)

  8. On a vehicle with automatic adjusters, the push rod stroke goes past the legal limit. What does this tell you?

    Under a truck at an axle: a round air brake chamber, its push rod, and the slack adjuster arm it joins on the end of a shaft that runs into the brake behind the wheel.
    • The adjusters need a routine turn by hand
    • A fault in the adjuster or brake parts
    • The brake chambers got too much air
    Show answer

    Correct answer: A fault in the adjuster or brake parts

    Automatic adjusters should keep the stroke in limits, so an over-limit stroke points to a fault in the adjuster, in the foundation brake parts, or to bad installation.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-121)

  9. What is routine hand adjustment of most automatic slack adjusters likely to cause?

    Under a truck at an axle: a round air brake chamber, its push rod, and the slack adjuster arm it joins on the end of a shaft that runs into the brake behind the wheel.
    • Early wear of the adjuster itself
    • Longer life for the brake linings
    • A shorter push rod stroke for good
    Show answer

    Correct answer: Early wear of the adjuster itself

    Adjusting most automatic adjusters by hand as a routine will probably wear the adjuster out early.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-122)

  10. Brakes with automatic adjusters are found out of adjustment. What is the recommended action?

    Under a truck at an axle: a round air brake chamber, its push rod, and the slack adjuster arm it joins on the end of a shaft that runs into the brake behind the wheel.
    • Turn the adjusters by hand and keep driving
    • Take the vehicle to a repair facility soon
    • Wait for the next scheduled inspection
    Show answer

    Correct answer: Take the vehicle to a repair facility soon

    Automatic adjusters that are out of adjustment point to a hidden fault, so the driver should get the vehicle to a shop soon.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-123)

  11. Why is turning an automatic slack adjuster by hand dangerous?

    Under a truck at an axle: a round air brake chamber, its push rod, and the slack adjuster arm it joins on the end of a shaft that runs into the brake behind the wheel.
    • It can make the brakes seem safe when they are not
    • It can cause the compressor to cut in too early
    • It always shortens the push rod stroke too far
    Show answer

    Correct answer: It can make the brakes seem safe when they are not

    Hand adjustment hides the real problem, so the driver may wrongly trust the braking system.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-124)

  12. On the road, brakes with automatic slack adjusters are found out of adjustment. When may they be adjusted by hand?

    Under a truck at an axle: a round air brake chamber, its push rod, and the slack adjuster arm it joins on the end of a shaft that runs into the brake behind the wheel.
    • Only as a short-term fix in an emergency
    • Every time you do a pre-trip inspection
    • Any time the brakes feel a little soft
    Show answer

    Correct answer: Only as a short-term fix in an emergency

    Hand adjustment of an automatic adjuster is only a temporary emergency measure, because the brake will likely soon be out of adjustment again.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-125)

  13. How long may a crack in a brake drum or disc be before it is a defect?

    • No longer than the full width of the friction area
    • No longer than half the width of the friction area
    • No longer than one inch in total
    Show answer

    Correct answer: No longer than half the width of the friction area

    Any crack over half the width of the friction area means the drum or disc is unfit.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-126)

  14. Which condition of a brake lining is a defect?

    • Loose, or soaked with oil or grease
    • Worn evenly but still above the limit
    • A lighter color than the brake shoe
    Show answer

    Correct answer: Loose, or soaked with oil or grease

    Linings that are loose or soaked with oil or grease cannot be used. They also must not be dangerously thin.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-127)

  15. On an air brake vehicle, the final air brake check takes the place of which check?

    • The hydraulic brake check
    • The walk-around slack adjuster check
    • The engine compartment belt check
    Show answer

    Correct answer: The hydraulic brake check

    In the last step of the inspection, the air brake checks are done instead of the hydraulic brake check.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-128)

  16. How should the engine run while you check where the governor cuts out the compressor?

    • At a fast idle
    • At a slow idle
    • At full throttle in neutral
    Show answer

    Correct answer: At a fast idle

    You run the engine at a fast idle and watch the gauge. The reading should stop rising when the governor cuts out the compressor.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-129)

  17. In the governor check, how do you lower tank pressure to see the compressor cut in?

    A truck's dashboard seen from the cab while parked at a truck stop: a speedometer at zero, two round air pressure gauges labelled PRIMARY AIR and SECONDARY AIR, a yellow diamond-shaped knob labelled PARKING BRAKE and a red eight-sided knob labelled TRAILER AIR SUPPLY.
    • Press and release the brake with the engine idling
    • Pull the parking brake control out, then in
    • Switch the engine off and wait a while
    Show answer

    Correct answer: Press and release the brake with the engine idling

    Pumping the brake pedal with the engine idling drops the pressure until the compressor cuts in and the gauge starts to rise.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-130)

  18. What can a badly working air governor cause?

    The side of a truck's diesel engine: the air compressor bolted to the engine, with a finned top, metal lines leaving it and a small control valve mounted on its side.
    • Brake lights that stay on all the time
    • Spring brakes that never come on
    • Too little air pressure kept for safe driving
    Show answer

    Correct answer: Too little air pressure kept for safe driving

    If the governor does not cut the compressor in and out properly, the system may not hold enough air pressure to drive safely.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-131)

  19. In the first air leakage test, what do you do before timing the pressure drop?

    A truck's dashboard seen from the cab while parked at a truck stop: a speedometer at zero, two round air pressure gauges labelled PRIMARY AIR and SECONDARY AIR, a yellow diamond-shaped knob labelled PARKING BRAKE and a red eight-sided knob labelled TRAILER AIR SUPPLY.
    • Keep the engine running and pull the parking brake out
    • Turn off the engine and pull the parking brake out
    • Turn off the engine and push the parking brake in
    Show answer

    Correct answer: Turn off the engine and push the parking brake in

    The system is fully charged, the engine is off and the parking brake is released (pushed in), then you time the drop in air pressure.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-132)

  20. In the first leakage test (engine off, parking brake released, foot off the brake), a single vehicle should lose less than how much air pressure in one minute?

    • Less than 5 psi
    • Less than 2 psi
    • Less than 8 psi
    Show answer

    Correct answer: Less than 2 psi

    For a single vehicle the loss should be under 2 psi in one minute.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-133)

  21. In the first leakage test (engine off, parking brake released, foot off the brake), a combination vehicle should lose less than how much air pressure in one minute?

    • Less than 6 psi
    • Less than 3 psi
    • Less than 8 psi
    Show answer

    Correct answer: Less than 3 psi

    For a combination vehicle the loss should be under 3 psi in one minute.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-134)

Part 221 questions
  1. Before the leakage test with the foot brake applied, air pressure is built up to governor cutoff. What range is that?

    • 120 to 140 psi
    • 60 to 80 psi
    • 150 to 170 psi
    Show answer

    Correct answer: 120 to 140 psi

    For this test the pressure is first built up to governor cutoff, which is 120 to 140 psi.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-135)

  2. In the foot-brake leakage test on a combination vehicle, which valve do you release along with the parking brake?

    • The tractor protection valve
    • The air tank safety valve
    • The front brake limiting valve
    Show answer

    Correct answer: The tractor protection valve

    On a combination vehicle you release both the parking brake and the tractor protection valve before applying the foot brake.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-136)

  3. In the leakage test with the foot brake applied, how long do you hold the brake?

    • Ten seconds
    • One minute
    • Five minutes
    Show answer

    Correct answer: One minute

    You fully apply the foot brake, hold it for one minute, and watch the air gauge.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-137)

  4. With the foot brake held fully applied, a single vehicle losing more than how much pressure in one minute is losing too much?

    • More than 6 psi
    • More than 3 psi
    • More than 8 psi
    Show answer

    Correct answer: More than 3 psi

    For a single vehicle, a drop of more than 3 psi in one minute with the foot brake applied is too much.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-138)

  5. With the foot brake held fully applied, a combination vehicle losing more than how much pressure in one minute is losing too much?

    • More than 4 psi
    • More than 7 psi
    • More than 10 psi
    Show answer

    Correct answer: More than 4 psi

    For a combination vehicle, a drop of more than 4 psi in one minute with the foot brake applied is too much.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-139)

  6. The air loss rate is too high. What must you do?

    • Drive on, but stay below normal speed
    • Find and fix the leaks before driving
    • Drive to a shop with the engine running
    Show answer

    Correct answer: Find and fix the leaks before driving

    Too much air loss means you could lose your brakes while driving, so the leaks must be found and fixed first.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-140)

  7. In the low pressure warning test, how do you lower the tank pressure once the engine is off?

    A parked truck's dashboard: a red lamp marked LOW AIR is lit above the two air pressure gauges, and both needles are low.
    • Open the manual drain valve on each tank
    • Rev the engine and let it idle
    • Turn the power on and pump the brake pedal
    Show answer

    Correct answer: Turn the power on and pump the brake pedal

    With the engine off and the electrical power on, pumping the brake pedal reduces the tank pressure so you can see when the signal comes on.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-141)

  8. In a dual air system, the low pressure warning test is judged by which tank?

    A parked truck's dashboard: a red lamp marked LOW AIR is lit above the two air pressure gauges, and both needles are low.
    • The tank with the highest pressure
    • The tank with the lowest pressure
    • Only the tank of the primary system
    Show answer

    Correct answer: The tank with the lowest pressure

    In a dual system the signal must come on before the tank with the lowest pressure falls below the warning level.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-142)

  9. The low pressure warning signal does not work. What could happen in a single-circuit air system?

    • The brake pedal becoming very hard to push
    • The compressor shutting off at once
    • Sudden emergency braking
    Show answer

    Correct answer: Sudden emergency braking

    Without a working warning you could lose air without knowing it, and a single-circuit system could brake suddenly and hard.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-143)

  10. The low pressure warning signal does not work. What happens in a dual air system when pressure is lost?

    A truck's dashboard while driving: both air pressure needles are low, and the warning lamp strip above them is dark.
    • The stopping distance gets longer
    • The vehicle stops sooner than normal
    • The compressor cuts out early
    Show answer

    Correct answer: The stopping distance gets longer

    In a dual system the stopping distance increases, and only limited braking is possible before the spring brakes come on.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-144)

  11. On a tractor-trailer, which valves should pop out as you keep fanning off the air pressure?

    • Only the tractor protection valve and the foot valve
    • The foot valve and the air tank drain valve
    • The tractor protection and parking brake valves
    Show answer

    Correct answer: The tractor protection and parking brake valves

    On a tractor-trailer both the tractor protection valve and the parking brake valve close and pop out when the pressure falls low enough, which puts the spring brakes on.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-145)

  12. On a single vehicle, which valve should pop out when you fan the air pressure down far enough?

    • The parking brake valve
    • The tractor protection valve
    • The safety relief valve
    Show answer

    Correct answer: The parking brake valve

    On single vehicles, and on combinations other than tractor-trailers, the parking brake valve is the one that closes.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-146)

  13. As you fan off the air pressure, at about what range of pressure should the valves pop out so the spring brakes come on?

    • 5 to 15 psi
    • 90 to 110 psi
    • 20 to 45 psi
    Show answer

    Correct answer: 20 to 45 psi

    The parking brake valve closes when the pressure falls to the maker’s specification of 20 to 45 psi, and the spring brakes come on.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-147)

  14. In a dual air system at operating rpms, how fast should pressure rise from 85 to 100 psi?

    • Within 20 seconds
    • Within 45 seconds
    • Within 90 seconds
    Show answer

    Correct answer: Within 45 seconds

    In a dual system, pressure should climb to 100 psi from 85 in 45 seconds or less with the engine at operating rpms.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-148)

  15. Why might a vehicle safely take longer than the usual time to build up air pressure?

    • Its air tanks are larger than the minimum size
    • It has an automatic wig wag warning device
    • It uses a modulating control valve to park
    Show answer

    Correct answer: Its air tanks are larger than the minimum size

    With air tanks larger than the minimum, a longer build-up time can still be safe. The manufacturer's specifications apply.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-149)

  16. In an older single air system, what is the typical time for pressure to build from 50 to 90 psi?

    • Within 1 minute
    • Within 3 minutes
    • Within 6 minutes
    Show answer

    Correct answer: Within 3 minutes

    An older single air system typically needs 3 minutes or less to go from 50 to 90 psi, with the engine idling.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-150)

  17. For the pressure build-up check on an older single air system, at what engine speed is the build-up timed?

    • An idle speed of 600 to 900 rpm
    • A fast idle of 1,200 to 1,500 rpm
    • Full governed engine speed
    Show answer

    Correct answer: An idle speed of 600 to 900 rpm

    Single air systems made before 1975 are typically timed with the engine idling at 600 to 900 rpm.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-151)

  18. The air pressure builds up too slowly. What should you do?

    • Drive, but avoid long hills
    • Drive, and drain the tanks at the end of the day
    • Do not drive until it is fixed
    Show answer

    Correct answer: Do not drive until it is fixed

    Slow build-up means pressure could fall too low on the road and force an emergency stop, so the problem must be fixed before driving.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-152)

  19. How do you test that the parking brake will hold?

    A truck's dashboard seen from the cab while parked at a truck stop: a speedometer at zero, two round air pressure gauges labelled PRIMARY AIR and SECONDARY AIR, a yellow diamond-shaped knob labelled PARKING BRAKE and a red eight-sided knob labelled TRAILER AIR SUPPLY.
    • Set it and tug gently against it in low gear
    • Set it and push the brake pedal firmly
    • Set it and rev the engine in neutral
    Show answer

    Correct answer: Set it and tug gently against it in low gear

    You stop, set the parking brake, and gently try to pull forward in a low gear. If the vehicle stays put, the brake holds.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-153)

  20. About how fast should you be moving when you test the service brakes?

    • About 15 mph
    • About 5 mph
    • About 25 mph
    Show answer

    Correct answer: About 5 mph

    You roll forward slowly at about 5 mph and press the brake pedal firmly.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-154)

  21. What should you watch for when you test the service brakes at low speed?

    • Compressor noise or a squealing drive belt
    • Tank drain valves leaking water or oil
    • A pull to one side or a late stop
    Show answer

    Correct answer: A pull to one side or a late stop

    During the low-speed test, notice if the vehicle pulls to one side, if the brakes feel unusual, or if they are slow to stop the vehicle.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-155)