Driving Test Practice
English

Your stateNot chosenChoose it to see the page numbers of your state's own CDL manual.

Air Brakes: Gauges, warnings and dual air systems — Part 2

Questions in this part include: “What does a front brake limiting valve do when its control is set to the slippery position?” · “In a dual air brake system, what does each of the two systems have of its own?”

Independent educational site · not affiliated with any government agency or DMV

Start the test

Ready? Test yourself

20 questions · About 8 min

Answer to start, or tap Start below:

What were front brake limiting valves meant to prevent?

  • Instant feedback with an explanation
  • Every answer cites its source in the manual
  • Your best score is saved on this device
  • Keyboard: press 1 to 3 to answer and Enter for the next question

Questions are written in our own words from the CDL manual; they are not the real test's questions. With your state chosen, every answer gives its page in your state's CDL manual. Without a state, answers cite the CDL manual, national model as printed by New Jersey (July 2017).

All 17 questions in this practice test

Take the test above first, then use this list to study. Tap “Show answer” to see the correct answer and explanation.

Show the questions and answersHide the questions
  1. What does a front brake limiting valve do when its control is set to the slippery position?

    An older truck's dash panel: a small lever under a plate marked FRONT BRAKES, with two positions marked NORMAL and SLIPPERY; the lever points to SLIPPERY.
    • It shuts the front brakes off completely
    • It cuts the rear brake pressure by half
    • It cuts the pressure to the front brakes by half
    Show answer

    Correct answer: It cuts the pressure to the front brakes by half

    In the slippery position the valve lowers the normal air pressure going to the front brakes by half.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-067)

  2. What were front brake limiting valves meant to prevent?

    • Front wheel skids on slippery surfaces
    • Rear wheel lockup on dry pavement
    • Trailer swing during sharp turns
    Show answer

    Correct answer: Front wheel skids on slippery surfaces

    They were fitted to make a front wheel skid less likely on a slippery road, though they really reduce stopping power.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-068)

  3. What is the real effect of a front brake limiting valve on stopping?

    An older truck's dash panel: a small lever under a plate marked FRONT BRAKES, with two positions marked NORMAL and SLIPPERY; the lever points to NORMAL.
    • It makes the vehicle weaker at stopping
    • It shortens the stopping distance on ice
    • It makes no difference to stopping power
    Show answer

    Correct answer: It makes the vehicle weaker at stopping

    Although the valves were meant to prevent front wheel skids, they actually lower the stopping power of the vehicle.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-069)

  4. What have tests shown about front wheel skids from braking on ice?

    • They are not likely
    • They happen on every hard stop
    • They happen only on loaded vehicles
    Show answer

    Correct answer: They are not likely

    Front brakes work well in every condition, and tests show front wheel skids are not likely even on ice.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-070)

  5. Where should you keep the cab control of a front brake limiting valve?

    • In the slippery position
    • Halfway between the two positions
    • In the normal position
    Show answer

    Correct answer: In the normal position

    Keep the control in the normal position. The slippery position cuts front brake pressure and weakens stopping.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-071)

  6. An automatic front wheel limiting valve cuts air to the front brakes, except when braking at what application pressure?

    • 55 psi or more
    • 20 psi or more
    • 90 psi or more
    Show answer

    Correct answer: 55 psi or more

    The valve lowers the air to the front brakes unless you brake very hard, at 55 psi or more application pressure.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-072)

  7. What can the driver do to adjust an automatic front wheel limiting valve?

    • Turn it off with the parking brake knob
    • Nothing, because the driver cannot control it
    • Switch it with a lever on the dash
    Show answer

    Correct answer: Nothing, because the driver cannot control it

    Automatic front wheel limiting valves work on their own and the driver has no control over them.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-073)

  8. How are the two systems of a dual air brake operated?

    • The primary system uses the pedal and the secondary uses its own pedal
    • Both systems share one set of brake controls
    • The secondary system works only when the parking brake is set
    Show answer

    Correct answer: Both systems share one set of brake controls

    A dual air brake has two separate systems, each with its own tanks, hoses and lines, but they work from one set of brake controls.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-074)

  9. In a dual air brake system, what does each of the two systems have of its own?

    • A brake pedal and a parking knob
    • Air tanks, hoses and lines
    • A compressor and a governor
    Show answer

    Correct answer: Air tanks, hoses and lines

    Each of the two systems has separate air tanks, hoses and lines.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-075)

  10. In a typical dual air brake, what does one of the two systems operate?

    • Only the brakes of a trailer that is being towed
    • The ordinary rear axle brakes, one axle or more
    • Only the spring brakes that hold the vehicle parked
    Show answer

    Correct answer: The ordinary rear axle brakes, one axle or more

    One system typically runs the ordinary brakes at the rear, while the other runs those at the front, and maybe at one rear axle too.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-076)

  11. In a typical dual air brake, one system works the rear axle brakes. What does the other system work?

    • Only the trailer's service brakes
    • Only the spring brakes for parking
    • The front axle, and maybe one rear axle
    Show answer

    Correct answer: The front axle, and maybe one rear axle

    The second system runs the regular brakes at the front axle, and sometimes at one rear axle too.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-077)

  12. In a dual air brake, which system supplies air to a trailer?

    • Only the primary system
    • Only the secondary system
    • Both systems
    Show answer

    Correct answer: Both systems

    Both the primary and the secondary system feed any attached trailer.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-078)

  13. What are the two systems of a dual air brake called?

    • Leading and backup
    • Service and spare
    • Primary and secondary
    Show answer

    Correct answer: Primary and secondary

    The two systems are called the primary system and the secondary system.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-079)

  14. Before you drive a vehicle with a dual air system, how much pressure should the compressor build?

    • At least 125 psi in the primary system only
    • At least 85 psi in either system
    • At least 100 psi in both systems
    Show answer

    Correct answer: At least 100 psi in both systems

    Wait until both the primary and secondary systems hold at least 100 psi before you drive.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-080)

  15. In a dual air system, when should the warning light and buzzer turn off while pressure builds?

    A parked truck's dashboard: a red lamp marked LOW AIR is lit above the two air pressure gauges, and both needles are low.
    • As soon as the primary system reaches the maker's value
    • The moment the engine starts, whatever the pressure
    • When both systems pass the maker's value, which is above 55 psi
    Show answer

    Correct answer: When both systems pass the maker's value, which is above 55 psi

    The signal goes off only when both systems pass a value set by the manufacturer, and that value must be greater than 55 psi.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-081)

  16. In a dual air system, the low pressure warning must come on before 55 psi is reached in which system?

    A truck's dashboard seen from the cab while parked at a truck stop: a speedometer at zero, two round air pressure gauges labelled PRIMARY AIR and SECONDARY AIR, a yellow diamond-shaped knob labelled PARKING BRAKE and a red eight-sided knob labelled TRAILER AIR SUPPLY.
    • Only the primary system
    • Either system
    • Only when both systems are low together
    Show answer

    Correct answer: Either system

    The warning must come on before pressure drops below 55 psi in either the primary or the secondary system.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-082)

  17. What happens when one half of a dual air brake system is very low on pressure?

    A truck's dashboard while driving: a red lamp marked LOW AIR is lit, the PRIMARY AIR gauge shows normal pressure and the SECONDARY AIR needle is very low.
    • The other half works harder and the stop is shorter
    • The front or rear brakes lose full action and stopping takes longer
    • Only the trailer brakes are lost and stopping is unchanged
    Show answer

    Correct answer: The front or rear brakes lose full action and stopping takes longer

    One end of the vehicle, front or rear, loses full braking, so the vehicle needs more distance to stop.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-083)