Driving Test Practice
English

Your stateNot chosenChoose it to see the page numbers of your state's own CDL manual.

Air Brakes: Gauges, warnings and dual air systems

Supply and application pressure gauges, the low air pressure warning, the stop light switch, front brake limiting valves and dual air brake systems. Split into 2 shorter tests so you're not stuck in one long quiz.

Independent educational site · not affiliated with any government agency or DMV

All 34 Gauges, warnings and dual air systems questions with answers

Choose a part above to take a practice test, or study every question and answer here.

Show the questions and answersHide the questions
Part 117 questions
  1. A truck has a dual air brake system. How is its supply pressure shown?

    • A separate gauge for each half, or one gauge with two needles
    • One gauge with a single needle for both halves
    • One gauge for the front half and a warning light for the rear half
    Show answer

    Correct answer: A separate gauge for each half, or one gauge with two needles

    Each half of a dual system has its own reading, either on two gauges or on one gauge with two needles.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-050)

  2. What does the supply pressure gauge on an air brake vehicle show you?

    A truck's dashboard seen from the cab while parked at a truck stop: a speedometer at zero, two round air pressure gauges labelled PRIMARY AIR and SECONDARY AIR, a yellow diamond-shaped knob labelled PARKING BRAKE and a red eight-sided knob labelled TRAILER AIR SUPPLY.
    • The air pressure your foot sends to the brakes
    • The air pressure where the governor starts the compressor
    • The air pressure waiting in the air tanks
    Show answer

    Correct answer: The air pressure waiting in the air tanks

    The supply gauges report how much pressure is stored in the air tanks. A different gauge, not found on every vehicle, shows how hard you are applying the brakes.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-051)

  3. What does an application pressure gauge tell the driver?

    A truck's dashboard while driving: a speedometer and three round air gauges in a row labelled PRIMARY, SECONDARY and APPLICATION; the APPLICATION needle is part way up.
    • The air pressure being sent to the brakes
    • The amount of air left in the tanks
    • The pressure level where the low air warning starts
    Show answer

    Correct answer: The air pressure being sent to the brakes

    The application gauge reports how much air pressure the driver is sending to the brakes while braking.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-052)

  4. Which of these gauges or devices is missing on some air brake vehicles?

    • The supply pressure gauge
    • The low air pressure warning signal
    • The application pressure gauge
    Show answer

    Correct answer: The application pressure gauge

    Every air brake vehicle has a supply gauge and a low pressure warning, but the application pressure gauge is not fitted on all vehicles.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-053)

  5. You must keep pressing harder, so the application gauge climbs, just to hold the same speed. What does this mean?

    A truck's dashboard while driving: a speedometer and three round air gauges in a row labelled PRIMARY, SECONDARY and APPLICATION; the APPLICATION needle is part way up.
    • The air compressor is cutting in
    • The brakes are fading
    • The air tanks are overfilled
    Show answer

    Correct answer: The brakes are fading

    Needing more and more application pressure to keep the same speed is a sign the brakes are fading from heat.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-054)

  6. The application gauge shows the brakes are fading. What should you do?

    A tractor-trailer coming down a long, steep mountain road, about to pass a yellow diamond warning sign that shows a truck on a slope.
    • Keep your speed and press the pedal harder
    • Shift to a higher gear and hold your speed
    • Slow down and shift to a lower gear
    Show answer

    Correct answer: Slow down and shift to a lower gear

    When brakes fade, reduce speed and use a lower gear so the engine helps hold the vehicle back.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-055)

  7. Besides fade, which problem can also make you need more application pressure?

    • Brakes that are out of adjustment
    • A governor set to cut out too high
    • An alcohol evaporator that needs filling
    Show answer

    Correct answer: Brakes that are out of adjustment

    Brakes that are out of adjustment, air leaks and mechanical problems can all make you need more application pressure.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-056)

  8. A vehicle with air brakes has a visible low pressure warning. It must come on before tank pressure falls below what level?

    • 40 psi
    • 70 psi
    • 55 psi
    Show answer

    Correct answer: 55 psi

    The visible warning signal must come on before the tank pressure drops below 55 psi.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-057)

  9. On older vehicles, the low pressure warning is tied to which pressure instead of a fixed number?

    • Half of the compressor governor cutout pressure
    • Half of the governor cut-in pressure
    • A quarter of the governor cutout pressure
    Show answer

    Correct answer: Half of the compressor governor cutout pressure

    On older vehicles the warning must come on before pressure falls below half of the governor cutout pressure.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-058)

  10. What does the low air pressure warning usually look like?

    • A red light, sometimes with a buzzer
    • A yellow light beside the mirror
    • A gauge needle that glows amber
    Show answer

    Correct answer: A red light, sometimes with a buzzer

    The low air pressure warning is normally a red light, and a buzzer may sound as well.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-059)

  11. How does a wig wag warn the driver of low air pressure?

    • A mechanical arm falls into the driver's view
    • A metal flag pops out beside the mirror
    • A lever pushes the parking brake knob out
    Show answer

    Correct answer: A mechanical arm falls into the driver's view

    A wig wag is a mechanical arm that drops into the driver's line of sight when system pressure is low.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-060)

  12. An automatic wig wag has dropped into view. When does it lift back out of view?

    Inside the cab of an older truck standing in a yard: a red metal arm with a plate reading LOW AIR hangs down in front of the windshield, in the driver's view; the air gauge needle is low.
    • When system pressure climbs past 55 psi
    • When the driver presses a reset button
    • When the parking brake knob is pushed in
    Show answer

    Correct answer: When system pressure climbs past 55 psi

    An automatic wig wag lifts out of view by itself once system pressure rises above 55 psi.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-061)

  13. How do you put a manual reset wig wag back out of view?

    Inside the cab of an older truck standing in a yard: a red metal arm with a plate reading LOW AIR hangs down in front of the windshield, in the driver's view; the air gauge needle is low.
    • Move it to the out of view position by hand
    • Wait until it rises on its own as pressure builds
    • Press the brake pedal several times quickly
    Show answer

    Correct answer: Move it to the out of view position by hand

    A manual reset wig wag does not rise by itself. The driver must place it in the out of view position.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-062)

  14. At about what pressure do the low pressure warning devices on large buses commonly signal?

    • 40 to 45 psi
    • 80 to 85 psi
    • 100 to 105 psi
    Show answer

    Correct answer: 80 to 85 psi

    Large buses commonly signal low pressure at 80 to 85 psi.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-063)

  15. What turns on the brake lights when you apply the air brakes?

    The back of a truck trailer at dusk, seen from the vehicle behind: its four round red brake lamps are lit.
    • A cable attached to the brake pedal
    • A sensor inside each brake drum
    • An electric switch worked by air pressure
    Show answer

    Correct answer: An electric switch worked by air pressure

    The stop light switch is an electric switch operated by air pressure. It lights the brake lights to warn drivers behind you.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-064)

  16. Front brake limiting valves with a cab control are found on vehicles made before which year?

    • 1975
    • 1965
    • 1985
    Show answer

    Correct answer: 1975

    Some vehicles built before 1975 had a limiting valve with a control in the cab.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-065)

  17. Which two words usually mark the cab control of a front brake limiting valve?

    • City and highway
    • Loaded and empty
    • Normal and slippery
    Show answer

    Correct answer: Normal and slippery

    Its two positions are labeled normal and slippery.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-066)

Part 217 questions
  1. What does a front brake limiting valve do when its control is set to the slippery position?

    An older truck's dash panel: a small lever under a plate marked FRONT BRAKES, with two positions marked NORMAL and SLIPPERY; the lever points to SLIPPERY.
    • It shuts the front brakes off completely
    • It cuts the rear brake pressure by half
    • It cuts the pressure to the front brakes by half
    Show answer

    Correct answer: It cuts the pressure to the front brakes by half

    In the slippery position the valve lowers the normal air pressure going to the front brakes by half.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-067)

  2. What were front brake limiting valves meant to prevent?

    • Front wheel skids on slippery surfaces
    • Rear wheel lockup on dry pavement
    • Trailer swing during sharp turns
    Show answer

    Correct answer: Front wheel skids on slippery surfaces

    They were fitted to make a front wheel skid less likely on a slippery road, though they really reduce stopping power.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-068)

  3. What is the real effect of a front brake limiting valve on stopping?

    An older truck's dash panel: a small lever under a plate marked FRONT BRAKES, with two positions marked NORMAL and SLIPPERY; the lever points to NORMAL.
    • It makes the vehicle weaker at stopping
    • It shortens the stopping distance on ice
    • It makes no difference to stopping power
    Show answer

    Correct answer: It makes the vehicle weaker at stopping

    Although the valves were meant to prevent front wheel skids, they actually lower the stopping power of the vehicle.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-069)

  4. What have tests shown about front wheel skids from braking on ice?

    • They are not likely
    • They happen on every hard stop
    • They happen only on loaded vehicles
    Show answer

    Correct answer: They are not likely

    Front brakes work well in every condition, and tests show front wheel skids are not likely even on ice.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-070)

  5. Where should you keep the cab control of a front brake limiting valve?

    • In the slippery position
    • Halfway between the two positions
    • In the normal position
    Show answer

    Correct answer: In the normal position

    Keep the control in the normal position. The slippery position cuts front brake pressure and weakens stopping.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-071)

  6. An automatic front wheel limiting valve cuts air to the front brakes, except when braking at what application pressure?

    • 55 psi or more
    • 20 psi or more
    • 90 psi or more
    Show answer

    Correct answer: 55 psi or more

    The valve lowers the air to the front brakes unless you brake very hard, at 55 psi or more application pressure.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-072)

  7. What can the driver do to adjust an automatic front wheel limiting valve?

    • Turn it off with the parking brake knob
    • Nothing, because the driver cannot control it
    • Switch it with a lever on the dash
    Show answer

    Correct answer: Nothing, because the driver cannot control it

    Automatic front wheel limiting valves work on their own and the driver has no control over them.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-073)

  8. How are the two systems of a dual air brake operated?

    • The primary system uses the pedal and the secondary uses its own pedal
    • Both systems share one set of brake controls
    • The secondary system works only when the parking brake is set
    Show answer

    Correct answer: Both systems share one set of brake controls

    A dual air brake has two separate systems, each with its own tanks, hoses and lines, but they work from one set of brake controls.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-074)

  9. In a dual air brake system, what does each of the two systems have of its own?

    • A brake pedal and a parking knob
    • Air tanks, hoses and lines
    • A compressor and a governor
    Show answer

    Correct answer: Air tanks, hoses and lines

    Each of the two systems has separate air tanks, hoses and lines.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-075)

  10. In a typical dual air brake, what does one of the two systems operate?

    • Only the brakes of a trailer that is being towed
    • The ordinary rear axle brakes, one axle or more
    • Only the spring brakes that hold the vehicle parked
    Show answer

    Correct answer: The ordinary rear axle brakes, one axle or more

    One system typically runs the ordinary brakes at the rear, while the other runs those at the front, and maybe at one rear axle too.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-076)

  11. In a typical dual air brake, one system works the rear axle brakes. What does the other system work?

    • Only the trailer's service brakes
    • Only the spring brakes for parking
    • The front axle, and maybe one rear axle
    Show answer

    Correct answer: The front axle, and maybe one rear axle

    The second system runs the regular brakes at the front axle, and sometimes at one rear axle too.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-077)

  12. In a dual air brake, which system supplies air to a trailer?

    • Only the primary system
    • Only the secondary system
    • Both systems
    Show answer

    Correct answer: Both systems

    Both the primary and the secondary system feed any attached trailer.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-078)

  13. What are the two systems of a dual air brake called?

    • Leading and backup
    • Service and spare
    • Primary and secondary
    Show answer

    Correct answer: Primary and secondary

    The two systems are called the primary system and the secondary system.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-079)

  14. Before you drive a vehicle with a dual air system, how much pressure should the compressor build?

    • At least 125 psi in the primary system only
    • At least 85 psi in either system
    • At least 100 psi in both systems
    Show answer

    Correct answer: At least 100 psi in both systems

    Wait until both the primary and secondary systems hold at least 100 psi before you drive.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-080)

  15. In a dual air system, when should the warning light and buzzer turn off while pressure builds?

    A parked truck's dashboard: a red lamp marked LOW AIR is lit above the two air pressure gauges, and both needles are low.
    • As soon as the primary system reaches the maker's value
    • The moment the engine starts, whatever the pressure
    • When both systems pass the maker's value, which is above 55 psi
    Show answer

    Correct answer: When both systems pass the maker's value, which is above 55 psi

    The signal goes off only when both systems pass a value set by the manufacturer, and that value must be greater than 55 psi.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-081)

  16. In a dual air system, the low pressure warning must come on before 55 psi is reached in which system?

    A truck's dashboard seen from the cab while parked at a truck stop: a speedometer at zero, two round air pressure gauges labelled PRIMARY AIR and SECONDARY AIR, a yellow diamond-shaped knob labelled PARKING BRAKE and a red eight-sided knob labelled TRAILER AIR SUPPLY.
    • Only the primary system
    • Either system
    • Only when both systems are low together
    Show answer

    Correct answer: Either system

    The warning must come on before pressure drops below 55 psi in either the primary or the secondary system.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-082)

  17. What happens when one half of a dual air brake system is very low on pressure?

    A truck's dashboard while driving: a red lamp marked LOW AIR is lit, the PRIMARY AIR gauge shows normal pressure and the SECONDARY AIR needle is very low.
    • The other half works harder and the stop is shorter
    • The front or rear brakes lose full action and stopping takes longer
    • Only the trailer brakes are lost and stopping is unchanged
    Show answer

    Correct answer: The front or rear brakes lose full action and stopping takes longer

    One end of the vehicle, front or rear, loses full braking, so the vehicle needs more distance to stop.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 5 (July 2017)⁩

    Report a problem with this question (cdl-ab-s5-083)