Driving Test Practice
English

Your stateNot chosenChoose it to see the page numbers of your state's own CDL manual.

General Knowledge: Transporting cargo safely

Inspecting cargo, weight and balance, securing cargo, and cargo that needs special attention. Split into 3 shorter tests so you're not stuck in one long quiz.

Independent educational site · not affiliated with any government agency or DMV

All 55 Transporting cargo safely questions with answers

Choose a part above to take a practice test, or study every question and answer here.

Show the questions and answersHide the questions
Part 119 questions
  1. What can happen to your own vehicle if it is carrying more than it should?

    • The vehicle itself can be damaged
    • Only the cargo can be damaged, not the truck
    • Damage only happens to the trailer floor
    Show answer

    Correct answer: The vehicle itself can be damaged

    An overloaded vehicle can suffer damage from the extra weight.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-872)

  2. How can the way a truck is loaded affect your driving?

    • It mainly changes how the mirrors must be set
    • It can make steering and control more difficult
    • It mostly changes how far the fuel will last
    Show answer

    Correct answer: It can make steering and control more difficult

    Poor loading can affect steering and make the vehicle harder to control.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-873)

  3. A warehouse crew loads and ties down your truck. Who is responsible for the safety of the cargo on the road?

    • Only the crew that loaded and tied down the cargo
    • You, as the driver, even though you did not load it
    • The company that owns the goods being hauled
    Show answer

    Correct answer: You, as the driver, even though you did not load it

    A driver stays responsible for the cargo no matter who loaded or secured it. That includes inspecting it and spotting problems.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-874)

  4. Besides being secured, what must be true about your load as far as your vision is concerned?

    • It must not hide the view through the rear window
    • It must not hide what is ahead or beside you
    • It must not reach higher than the top of the cab
    Show answer

    Correct answer: It must not hide what is ahead or beside you

    The driver must know that the load does not block the view ahead or to the sides.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-875)

  5. What must you make sure your cargo does not do with regard to emergency equipment?

    • Make it hard to reach emergency equipment
    • Add extra weight on top of the equipment box
    • Cover the warning labels on the equipment
    Show answer

    Correct answer: Make it hard to reach emergency equipment

    The cargo must never limit your access to emergency equipment on the vehicle.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-876)

  6. What extra credential do you need to haul hazardous material that requires placards on the vehicle?

    The rear of a white box truck backed to a loading dock: a red diamond placard with a white flame and the number 3 on its rear door and on its side, and steel drums on a pallet on the dock.
    • A hazardous materials endorsement
    • A tank vehicle endorsement
    • A special oversize-load permit
    Show answer

    Correct answer: A hazardous materials endorsement

    Carrying placarded hazardous material requires a hazardous materials endorsement on your CDL.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-877)

  7. How often should you re-check your cargo and tie-downs during a trip, beyond the set times?

    • Only at the 3-hour and 150-mile marks
    • Only at the start and end of each day
    • As often as needed to keep the load secure
    Show answer

    Correct answer: As often as needed to keep the load secure

    Check as often as needed during the trip so that the load stays secure.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-878)

  8. During a long trip, how often must you re-check the load and its securing devices, going by driving time or distance?

    • After 3 hours or 150 miles of driving
    • After 2 hours or 100 miles of driving
    • After 5 hours or 250 miles of driving
    Show answer

    Correct answer: After 3 hours or 150 miles of driving

    Re-inspect the cargo after every 3 hours or 150 miles of driving.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-879)

  9. Besides time and distance on the road, what else is a reason to look at your cargo again?

    • Each time you pass through a weigh station
    • Each time you cross into a new state
    • Each time you take a break from driving
    Show answer

    Correct answer: Each time you take a break from driving

    You must inspect the cargo again after every break you take while driving.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-880)

  10. The rules on cargo weight, covering loads and where big trucks may drive are not the same everywhere. What should you do?

    • Follow the rules of the state that issued your CDL
    • Follow only the federal rules on every route
    • Learn the rules for every place you will be driving
    Show answer

    Correct answer: Learn the rules for every place you will be driving

    Federal, state and local rules differ from place to place, so you must know the rules where you drive.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-881)

  11. Who is responsible for making sure a commercial vehicle is not overloaded?

    • The driver of the vehicle
    • The shipper who prepared the freight
    • The scale operator at the weigh station
    Show answer

    Correct answer: The driver of the vehicle

    The driver is responsible for not driving an overloaded vehicle.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-882)

  12. What does the GVWR of a vehicle measure?

    • The weight one axle puts on the road
    • The loaded weight set by its maker
    • The empty weight of a single vehicle
    Show answer

    Correct answer: The loaded weight set by its maker

    GVWR is the loaded weight of a single vehicle as specified by its manufacturer.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-883)

  13. What is meant by axle weight?

    • The total weight of the whole loaded vehicle
    • The most weight a tire can safely carry
    • The weight one axle puts on the ground
    Show answer

    Correct answer: The weight one axle puts on the ground

    Axle weight is how much load one axle, or one group of axles, puts onto the road.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-884)

  14. Where can you find the maximum safe load a tire can carry at a given pressure?

    • On the side of the tire
    • On the label inside the driver door
    • On the tread surface of the tire
    Show answer

    Correct answer: On the side of the tire

    The tire load rating is printed on the side of each tire.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-885)

  15. What does a coupling device capacity rating tell you?

    • The top speed the connection allows with a load
    • The most weight the device can pull or carry
    • The number of trailers that may be connected
    Show answer

    Correct answer: The most weight the device can pull or carry

    A coupling device has a rating for the heaviest load it can tow or support.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-886)

  16. Which weights have maximum limits set by the states?

    • Cargo weight, tire weight and fuel weight
    • Gross vehicle, combination and axle weights
    • Gross vehicle weight and trailer length only
    Show answer

    Correct answer: Gross vehicle, combination and axle weights

    States limit the gross vehicle weight rating, the gross combination weight rating and the axle weights, and you must stay within them.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-887)

  17. Under a bridge formula, how much weight is allowed on axles that are close together?

    • The same as for axles far apart
    • Less than for axles far apart
    • More than for axles far apart
    Show answer

    Correct answer: Less than for axles far apart

    Axles that are closer together are allowed less maximum weight, which protects bridges and roadways from overloading.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-888)

  18. What is a danger of an overloaded truck when going down a long hill?

    A tractor-trailer coming down a long, steep mountain road, about to pass a yellow diamond warning sign that shows a truck on a slope.
    • Its trailer may lift off the fifth wheel
    • It may slow down too much for traffic
    • It may pick up too much speed
    Show answer

    Correct answer: It may pick up too much speed

    An overloaded truck crawls up hills and can gain too much speed going down them.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-889)

  19. How does an overloaded truck behave when climbing a hill?

    • It climbs at normal speed in a lower gear
    • It has to go very slowly
    • It holds speed if the driver downshifts early
    Show answer

    Correct answer: It has to go very slowly

    An overloaded truck has to crawl up grades.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-890)

Part 218 questions
  1. Which of these is an effect of overloading a truck?

    • The truck turns quicker in curves
    • Hills can be climbed at the usual speed
    • Stopping distance increases
    Show answer

    Correct answer: Stopping distance increases

    Overloading makes the distance needed to stop longer.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-891)

  2. Why can overloading lead to brake failure?

    • The brake fluid cannot cope with extra weight
    • The brakes are forced to work too hard
    • The tires lose contact with the brake drums
    Show answer

    Correct answer: The brakes are forced to work too hard

    With too much weight the brakes must work harder than they were built to, and they can fail.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-892)

  3. In which conditions may it be unsafe to haul even the legal maximum weight?

    • On flat roads in light traffic
    • In bad weather or in the mountains
    • On roads that are very new or recently paved
    Show answer

    Correct answer: In bad weather or in the mountains

    Bad weather and mountain driving can make legal maximum weights unsafe, so think about this before driving.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-893)

  4. When is a vehicle with a high center of gravity most in danger of tipping over?

    • While parked on level ground
    • During a long, straight highway run
    • In curves or when swerving around a hazard
    Show answer

    Correct answer: In curves or when swerving around a hazard

    A high load makes tipping more likely, and the risk is greatest in curves or sudden swerves.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-894)

  5. How should you arrange parts of a load that differ in weight?

    • Heaviest pieces go on top so they press down
    • Pieces go in any order if tie-downs are used
    • Heaviest pieces go beneath the lightest pieces
    Show answer

    Correct answer: Heaviest pieces go beneath the lightest pieces

    Keeping the load low, with the heaviest pieces under the lighter ones, lowers the center of gravity.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-895)

  6. What can happen when too much of the load sits on the steering axle?

    • The engine overheats because the drive wheels carry too little
    • The truck steers with difficulty and the axle and tires can be damaged
    • The tie-downs stretch and the load slides toward the cab
    Show answer

    Correct answer: The truck steers with difficulty and the axle and tires can be damaged

    A steering axle that carries too much weight makes the truck hard to steer. The axle and its tires can also be damaged.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-896)

  7. Cargo is loaded too far toward the rear of the vehicle. What problem can this cause at the front?

    • The steering axle is too light to steer the vehicle safely
    • The steering axle gets too heavy and the steering wheel turns hard
    • The front brakes lock up each time the driver slows down
    Show answer

    Correct answer: The steering axle is too light to steer the vehicle safely

    Loading too far to the rear takes weight off the front axle. With too little weight on it, the truck cannot be steered safely.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-897)

  8. What is the risk when the driving axles carry too little weight?

    • The drive wheels may spin easily because traction is poor
    • The load is more likely to slide off a flatbed
    • The truck steers with extra effort at low speeds
    Show answer

    Correct answer: The drive wheels may spin easily because traction is poor

    Weight on the drive axles presses the tires onto the road. If there is too little, the drive wheels lose traction and spin, and in bad weather the truck may not keep moving.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-898)

  9. A load is stacked so its weight sits high above the road. What danger goes up?

    A flatbed trailer parked in a yard: a tall, narrow crate stands on the deck held by chains and straps, and a steel header board stands at the front of the deck just behind the cab.
    • Tire blowouts
    • Loss of engine power
    • Rollover
    Show answer

    Correct answer: Rollover

    A high center of gravity makes a vehicle tip over more easily, so a rollover becomes more likely.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-899)

  10. On a flatbed vehicle, what extra problem can come from a load with a high center of gravity?

    A flatbed trailer parked in a yard: a tall, narrow crate stands on the deck held by chains and straps, and a steel header board stands at the front of the deck just behind the cab.
    • The load may shift sideways or fall off
    • The header board may bend forward
    • The front axle may bend under the load
    Show answer

    Correct answer: The load may shift sideways or fall off

    A flatbed has no sides, so a high load is more likely to move to one side or drop off the vehicle.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-900)

  11. Which method places pieces shaped to fit snugly against the front, back or sides of cargo so it cannot slide?

    Inside a van trailer: a large wooden crate against the front wall, with short timbers nailed to the floor tight against its base and long timbers running at a slant from its top down to the floor and across to the side wall.
    • Blocking
    • Bracing
    • Tie-down
    Show answer

    Correct answer: Blocking

    Blocking is fitted tightly against the cargo and secured to the cargo deck, so the cargo cannot slide.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-901)

  12. What do you call a support that runs from the top part of the cargo down to the floor or walls of the cargo compartment?

    Inside a van trailer: a large wooden crate against the front wall, with short timbers nailed to the floor tight against its base and long timbers running at a slant from its top down to the floor and across to the side wall.
    • Blocking
    • A header board
    • Bracing
    Show answer

    Correct answer: Bracing

    Bracing reaches down from the top of the cargo to the floor or walls, which stops the cargo from moving.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-902)

  13. Your trailer has no sides. What must be done with the cargo?

    • Secure it so it cannot shift or fall off
    • Let it rest in place if it is heavy enough
    • Cover it only if the weather is bad
    Show answer

    Correct answer: Secure it so it cannot shift or fall off

    With no sides to hold it in, cargo on a flatbed or open trailer must be secured so it cannot move or drop off.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-903)

  14. Why can tie-downs still matter inside a closed van?

    • Tie-downs keep the van doors from opening
    • Shifting cargo can change how the vehicle handles
    • A closed van is lawful only with tie-downs on every box
    Show answer

    Correct answer: Shifting cargo can change how the vehicle handles

    Even where cargo cannot fall out, a load that moves inside the van can upset the way the vehicle handles.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-904)

  15. What must be true of the tie-downs you choose?

    • They must be chains, never ropes or straps
    • They must be the proper type and strength
    • They must be fitted only at the rear of the load
    Show answer

    Correct answer: They must be the proper type and strength

    Tie-downs have to suit the job: the right kind and enough strength for the load.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-905)

  16. By federal rules, the combined working load limit of the tie-downs must be at least what part of the cargo's weight?

    • Half of the weight of the cargo
    • The full weight of the cargo
    • Twice the weight of the cargo
    Show answer

    Correct answer: Half of the weight of the cargo

    The securement system's aggregate working load limit must reach at least one-half of the weight of the cargo it holds.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-906)

  17. Which of these is a tensioning device used with tie-downs?

    • A winch
    • A hook
    • A rail
    Show answer

    Correct answer: A winch

    Winches, ratchets and clinching components tighten tie-downs. Hooks, bolts, rails and rings are the places where tie-downs attach to the vehicle.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-907)

  18. What is the least number of tie-downs you need for a long load?

    • One for each five feet of cargo
    • One for each twenty feet of cargo
    • One for each ten feet of cargo
    Show answer

    Correct answer: One for each ten feet of cargo

    Use at least one tie-down for every ten feet of cargo, and add more if needed to meet that count.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-908)

Part 318 questions
  1. A very small piece of cargo is on your flatbed. How many tie-downs should it have at the least?

    • One
    • Three
    • Two
    Show answer

    Correct answer: Two

    Even tiny cargo needs at least two tie-downs, whatever its size.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-909)

  2. You are asked to haul heavy pieces of metal. What should you do before taking the job?

    • Use one extra tie-down beyond the usual count
    • Rely on blocking alone for metal pieces
    • Learn the special requirements for such loads
    Show answer

    Correct answer: Learn the special requirements for such loads

    Heavy metal pieces have their own securing requirements, so learn them before taking such a load.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-910)

  3. What is the job of the front-end header board behind the cab?

    A flatbed trailer parked in a yard: a tall, narrow crate stands on the deck held by chains and straps, and a steel header board stands at the front of the deck just behind the cab.
    • It protects you if the cargo moves forward in a stop
    • It keeps rain and snow from reaching the cargo
    • It keeps spilled cargo from hitting cars behind
    Show answer

    Correct answer: It protects you if the cargo moves forward in a stop

    The header board is a barrier between the cargo and the cab. It blocks cargo from moving forward onto the driver.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-911)

  4. Besides keeping weather off the load, why do drivers cover cargo?

    A flatbed trailer on a two-lane highway, seen from behind: its load is covered by a green tarp pulled tight and held down by straps.
    • To hide the cargo from theft
    • To keep the load from shifting in curves
    • So fallen cargo cannot hurt people
    Show answer

    Correct answer: So fallen cargo cannot hurt people

    A cover keeps pieces of cargo from spilling onto other people, and it also protects the load from the weather.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-912)

  5. Rules about covering a load to stop spills are a safety requirement in many states. What should a driver do about this?

    A flatbed trailer on a two-lane highway, seen from behind: its load is covered by a green tarp pulled tight and held down by straps.
    • Follow only the laws of the home state
    • Learn the laws of each state you drive in
    • Assume one national rule is the same everywhere
    Show answer

    Correct answer: Learn the laws of each state you drive in

    Spill protection is required in many states, and the laws differ, so the driver must know the rules where he or she drives.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-913)

  6. Why should you glance at your cargo cover in the mirrors while you drive?

    • The cover shrinks as it dries and makes the tie-downs slack
    • A flapping cover can tear loose and block someone's view
    • The cover shows if the load weighs too much for the axles
    Show answer

    Correct answer: A flapping cover can tear loose and block someone's view

    A cover that flaps may rip free, expose the load, and block the view of you or other drivers.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-914)

  7. Containerized loads are generally used when freight also travels part of its trip in what way?

    • By airplane or pipeline
    • By rail or ship
    • On the same truck for the whole route
    Show answer

    Correct answer: By rail or ship

    Containers are common when freight goes part of the way by rail or ship, with trucks making the delivery at the start or end.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-915)

  8. Some containers come with built-in fastening devices. Where do these attach?

    • To the tractor's rear bumper
    • Only to the cab's header board
    • Directly to a special frame
    Show answer

    Correct answer: Directly to a special frame

    Certain containers carry their own tie-down devices or locks, and these fasten straight to a special frame.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-916)

  9. A container has been loaded onto a flatbed trailer. How must it be handled?

    • It must be secured like any other cargo
    • It needs no securing because it is closed
    • Only the front end of it must be fastened
    Show answer

    Correct answer: It must be secured like any other cargo

    A container on a flatbed has to be secured properly, the same as any other load.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-917)

  10. You cannot look inside a sealed load. What should you still check before driving?

    • That the seal can be opened at each rest stop
    • That the cargo is stacked low inside the box
    • That you stay under gross and axle weight limits
    Show answer

    Correct answer: That you stay under gross and axle weight limits

    You cannot inspect sealed cargo, but you can still make sure the vehicle is within its gross weight and axle weight limits.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-918)

  11. Why do dry bulk tanks need special care?

    • The load can shift and the center of gravity is high
    • They have a low center of gravity that makes the steering light
    • They cannot carry weight over the drive axles
    Show answer

    Correct answer: The load can shift and the center of gravity is high

    A dry bulk tank sits high and its load can move, so go slowly and carefully around curves and sharp turns.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-919)

  12. With a load of hanging meat, where is special caution needed, with a slow speed?

    • Long, straight, flat highway sections
    • Weigh stations and truck inspection lanes
    • Sharp curves like off ramps and on ramps
    Show answer

    Correct answer: Sharp curves like off ramps and on ramps

    Hanging meat is top-heavy and unsteady, so slow down on sharp curves such as ramps.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-920)

  13. You are hauling livestock but the trailer is not full. What should you use?

    • Tie-downs on each animal
    • False bulkheads
    • A header board at the rear
    Show answer

    Correct answer: False bulkheads

    False bulkheads keep the animals bunched together so they cannot move around and upset handling.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-921)

  14. Why must you take extra care on curves even when livestock are bunched together?

    • The animals will panic from the engine noise
    • The bulkheads lose their strength in a curve
    • They can lean, shifting the center of gravity
    Show answer

    Correct answer: They can lean, shifting the center of gravity

    Livestock lean on curves, which moves the center of gravity and makes a rollover more likely.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-922)

  15. What do over-length, over-width or overweight loads need before they travel?

    A tractor pulling a low trailer that carries half of a factory-built house, wider than the trailer, on a two-lane highway: a yellow banner on the bumper reads OVERSIZE LOAD, flags mark the load's corners and amber lights are lit on the cab.
    • Special transit permits
    • A second CDL holder in the cab
    • A weigh-station stamp at each state line
    Show answer

    Correct answer: Special transit permits

    Loads that are too long, too wide or too heavy need special transit permits.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-923)

  16. What limit usually applies to when an oversized load may be driven?

    A tractor pulling a low trailer that carries half of a factory-built house, wider than the trailer, on a two-lane highway: a yellow banner on the bumper reads OVERSIZE LOAD, flags mark the load's corners and amber lights are lit on the cab.
    • Only on days with dry roads
    • Only after a police inspection each day
    • Only during certain times
    Show answer

    Correct answer: Only during certain times

    Oversized loads can usually be driven only at certain times set for them.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-924)

  17. Which equipment may a very large shipment need?

    • A reflective rear bumper
    • A "wide load" sign
    • An extra spare tire
    Show answer

    Correct answer: A "wide load" sign

    Oversized loads may need special equipment, such as signs saying wide load, flashing lights and flags.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-925)

  18. What may be required to travel with an oversized load?

    • A stop at every weigh station
    • A police escort or pilot vehicles
    • A second driver with a CDL
    Show answer

    Correct answer: A police escort or pilot vehicles

    Some oversized loads must be accompanied by a police escort or by pilot vehicles with warning signs or flashing lights.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s3-926)