Driving Test Practice
English

Your stateNot chosenChoose it to see the page numbers of your state's own CDL manual.

General Knowledge: Basic control and shifting gears

Accelerating, steering, stopping and backing safely, and shifting gears. Split into 2 shorter tests so you're not stuck in one long quiz.

Independent educational site · not affiliated with any government agency or DMV

All 46 Basic control and shifting gears questions with answers

Choose a part above to take a practice test, or study every question and answer here.

Show the questions and answersHide the questions
Part 123 questions
  1. When should a commercial driver have the seatbelt fastened?

    • Only when driving on a highway
    • Whenever the vehicle is on the road
    • Only when carrying a loaded trailer
    Show answer

    Correct answer: Whenever the vehicle is on the road

    The seatbelt is fastened any time you are driving on the road, not only in certain places or with certain loads.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-233)

  2. What should you do with the parking brake before you walk away from your vehicle?

    • Leave it off so the brakes do not stick
    • Apply it every time you leave the vehicle
    • Apply it only if you are on a slope
    Show answer

    Correct answer: Apply it every time you leave the vehicle

    Apply the parking brake whenever you leave your vehicle.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-234)

  3. You drive a manual transmission and start moving from a stop on a slope. What helps keep the vehicle from rolling back?

    A tractor-trailer standing still on a steep uphill road, stopped at a red traffic signal at the top of the grade, with a car waiting behind it.
    • Take your foot off the brake, then find the clutch
    • Partly engage the clutch before leaving the brake
    • Shift to neutral before leaving the brake pedal
    Show answer

    Correct answer: Partly engage the clutch before leaving the brake

    Partly engaging the clutch while your foot is still on the brake keeps the vehicle from rolling back into someone behind you.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-235)

  4. When is it right to release the parking brake while starting uphill?

    A tractor-trailer standing still on a steep uphill road, stopped at a red traffic signal at the top of the grade, with a car waiting behind it.
    • Before you touch the accelerator, to avoid brake wear
    • Once you have applied enough engine power to hold the vehicle
    • Right after you shift into the starting gear
    Show answer

    Correct answer: Once you have applied enough engine power to hold the vehicle

    Release the parking brake only after you have enough engine power applied, so the vehicle does not roll backward.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-236)

  5. A tractor-trailer has a trailer brake hand valve. How can it help when you start moving?

    A tractor-trailer standing still on a steep uphill road, stopped at a red traffic signal at the top of the grade, with a car waiting behind it.
    • It replaces the parking brake when you leave the cab
    • Setting it holds the rig so it does not roll backward
    • It keeps the trailer from jackknifing on a curve
    Show answer

    Correct answer: Setting it holds the rig so it does not roll backward

    Applying the trailer brake hand valve holds the combination in place so it does not roll backward as you start.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-237)

  6. How should you speed up a commercial vehicle?

    • As quickly as the engine allows, then level off
    • Smoothly, adding speed in a gradual way
    • In steps, pausing between each increase in speed
    Show answer

    Correct answer: Smoothly, adding speed in a gradual way

    Smooth, gradual acceleration keeps the vehicle from jerking. Rough acceleration can cause mechanical damage.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-238)

  7. What can harsh acceleration damage when you are pulling a trailer?

    • The landing gear that supports the trailer
    • The trailer's tires and the road surface
    • The coupling between the vehicle and the trailer
    Show answer

    Correct answer: The coupling between the vehicle and the trailer

    Rough acceleration puts a heavy strain on the coupling, so you should speed up smoothly and gradually.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-239)

  8. How should you accelerate when traction is poor, such as in rain or snow?

    A tractor-trailer with its headlamps on, on a wet two-lane road in winter: slush along the road's edges, spray at the wheels, snow on the roadside and on the fir trees.
    • Steadily, with the same power used on dry roads
    • Very gradually, adding power a little at a time
    • Normally, but with the clutch partly engaged
    Show answer

    Correct answer: Very gradually, adding power a little at a time

    On a slippery road, add speed very gradually. Using too much power can make the drive wheels spin.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-240)

  9. You are pulling away on a snowy road and the drive wheels start to spin. What should you do?

    • Shift up one gear to cut the power
    • Take your foot off the accelerator
    • Hold the accelerator still until they grip
    Show answer

    Correct answer: Take your foot off the accelerator

    Too much power can make the drive wheels spin, and you could lose control. When they start spinning, ease off the accelerator completely.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-241)

  10. How should you hold the steering wheel?

    • With one hand on top and the other free
    • With both hands firmly on opposite sides
    • With both hands close together at the top
    Show answer

    Correct answer: With both hands firmly on opposite sides

    A firm two-handed grip on opposite sides stops the wheel from being yanked out of your hands when a wheel strikes a curb or a pothole.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-242)

  11. What decides how much brake pressure you need for a normal stop?

    • The vehicle's speed and how quickly you must stop
    • The type of tires and the width of the lane
    • The engine size and the outside temperature
    Show answer

    Correct answer: The vehicle's speed and how quickly you must stop

    The pressure you need depends on your speed and how fast you need to stop. Push the pedal down gradually for a smooth, safe stop.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-243)

  12. With a manual transmission, when do you push the clutch in while stopping?

    • As soon as you begin to press the brake pedal
    • Only after the vehicle has come to a full stop
    • When the engine is close to idle
    Show answer

    Correct answer: When the engine is close to idle

    Push the clutch in when the engine speed has dropped close to idle, as you finish bringing the vehicle to a stop.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-244)

  13. Why should you try to park so that you can pull forward when you leave?

    Seen from above: a tractor-trailer stands straight in a warehouse yard, some distance from an empty loading dock bay between two parked trailers, with a light pole and pallets near its path.
    • Backing is always dangerous because you cannot see everything behind
    • Pulling forward saves fuel when the engine is cold
    • Backing wears out the transmission faster than driving forward
    Show answer

    Correct answer: Backing is always dangerous because you cannot see everything behind

    You cannot see everything behind the vehicle, so backing is always dangerous. Park so you can drive out forward.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-245)

  14. What decides the best starting position for a backing move?

    Seen from above: a tractor-trailer stands straight in a warehouse yard, some distance from an empty loading dock bay between two parked trailers, with a light pole and pallets near its path.
    • The weight of the cargo you are carrying
    • The type of backing you are going to do
    • Whether the trailer has air brakes or not
    Show answer

    Correct answer: The type of backing you are going to do

    The best spot to begin a safe backing move depends on what kind of backing you need to do.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-246)

  15. Before you back up, what should you do about your path?

    Seen from above: a tractor-trailer stands straight in a warehouse yard, some distance from an empty loading dock bay between two parked trailers, with a light pole and pallets near its path.
    • Get out, walk around, and check clearance to the sides and overhead
    • Sound the horn twice and begin backing when nobody answers
    • Check the mirrors once and then back at a steady pace
    Show answer

    Correct answer: Get out, walk around, and check clearance to the sides and overhead

    Walking around the vehicle lets you see obstacles and low clearances in and near the path before you start to move.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-247)

  16. While backing, you cannot be sure the path is clear. What should you do?

    Seen from above: a tractor-trailer stands straight in a warehouse yard, some distance from an empty loading dock bay between two parked trailers, with a light pole and pallets near its path.
    • Back slowly and rely on the horn
    • Keep going and watch only the driver's side mirror
    • Stop, step out, and look over the path yourself
    Show answer

    Correct answer: Stop, step out, and look over the path yourself

    Check the outside mirrors on both sides often, and if you are unsure, step out and look at the path yourself.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-248)

  17. Which gear should you use when backing, and why?

    Seen from above: a tractor-trailer stands straight in a warehouse yard, some distance from an empty loading dock bay between two parked trailers, with a light pole and pallets near its path.
    • The lowest reverse gear, so errors are easy to correct
    • The highest reverse gear, to finish the move sooner
    • Neutral, rolling back with the brakes lightly applied
    Show answer

    Correct answer: The lowest reverse gear, so errors are easy to correct

    The lowest reverse gear keeps your speed as slow as possible. That makes steering errors easier to fix and lets you stop quickly.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-249)

  18. Which direction is safest to turn when you back up, if you have a choice?

    • Toward the passenger side, near the curb
    • Either side, since the mirrors show both equally
    • Toward the driver's side, where you see better
    Show answer

    Correct answer: Toward the driver's side, where you see better

    Backing toward the driver's side lets you watch the rear of the vehicle through the side window. Even going around the block to set this up is worth it.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-250)

  19. Getting into position to back toward the driver's side means driving around the block. What should you do?

    • Back toward the right side to save time
    • Go around it; the safer view is worth it
    • Back straight in without turning at all
    Show answer

    Correct answer: Go around it; the safer view is worth it

    Driver-side backing gives you a better view, so it is worth going around the block to set it up.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-251)

  20. What is the main reason to use a helper when you back up?

    Seen from above: a tractor-trailer stands straight in a warehouse yard, some distance from an empty loading dock bay between two parked trailers, with a light pole and pallets near its path.
    • A helper lets you skip checking your mirrors
    • Some blind spots cannot be seen from the driver's seat
    • Most states require a helper for every backing move
    Show answer

    Correct answer: Some blind spots cannot be seen from the driver's seat

    There are blind spots you cannot see from the cab, so a helper is important whenever you can have one.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-252)

  21. Where should a helper stand while you are reversing?

    • Beside the driver's door so you can talk
    • In front of the cab, facing the driver
    • Near the rear of your vehicle
    Show answer

    Correct answer: Near the rear of your vehicle

    A helper near the rear can see the blind spots you cannot, and the helper should stand where you can see them.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-253)

  22. When should you and your helper agree on hand signals for backing?

    • After the first few feet of movement
    • Before you begin backing
    • Only if the mirrors are not working
    Show answer

    Correct answer: Before you begin backing

    Agree on hand signals, including one for stop, before backing starts, so both of you understand each other during the move.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-254)

  23. What is the result if you cannot get the vehicle into the right gear while driving?

    • You will have less control
    • You will use less fuel
    • You will have more braking power
    Show answer

    Correct answer: You will have less control

    Shifting correctly matters because the wrong gear leaves you with less control of the vehicle.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-255)

Part 223 questions
  1. A truck has a synchronized manual transmission. Does the driver need to double clutch?

    • No, it is not required
    • Yes, but only when shifting down
    • Yes, in every gear change
    Show answer

    Correct answer: No, it is not required

    Double clutching is not required with a synchronized manual transmission.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-256)

  2. What is the first move in the basic method for shifting up?

    • Let off the accelerator, push in the clutch and go to neutral together
    • Shift to neutral first, then let off the accelerator and push in the clutch
    • Push in the clutch and shift to neutral, then let off the accelerator
    Show answer

    Correct answer: Let off the accelerator, push in the clutch and go to neutral together

    The first move is a single combined action: release the accelerator, push in the clutch and shift to neutral together.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-257)

  3. When shifting up with the basic method, what happens after you release the clutch in neutral?

    • Press the accelerator to speed up the engine
    • Push the clutch in again and hold it down
    • Let the engine and gears slow to the next gear's rpm
    Show answer

    Correct answer: Let the engine and gears slow to the next gear's rpm

    After the clutch is released in neutral, you wait while the engine and gears lose speed to the rpm the higher gear needs.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-258)

  4. You waited too long in neutral and the next gear will not go in. What should you do?

    • Push the shift lever harder until it goes in
    • Stop the truck completely and turn the engine off, then start the shift over
    • Shift back to neutral, let the clutch out, rev the engine to road speed, then retry
    Show answer

    Correct answer: Shift back to neutral, let the clutch out, rev the engine to road speed, then retry

    Forcing the gear is the wrong move. Shift back to neutral, let the clutch out, bring engine speed up to road speed, then retry.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-259)

  5. If you decide when to shift up by engine speed, when do you shift?

    • At the middle of the operating rpm range
    • At the bottom of the operating rpm range
    • At the top of the operating rpm range
    Show answer

    Correct answer: At the top of the operating rpm range

    Learn the operating rpm range for your vehicle, watch the tachometer, and shift up when the engine reaches the top of that range.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-260)

  6. On a vehicle that uses progressive shifting, how does the shift rpm change as you move up through the gears?

    • It becomes lower in each higher gear
    • It becomes higher in each higher gear
    • It stays the same in every gear
    Show answer

    Correct answer: It becomes higher in each higher gear

    With this style of shifting, the rpm for each shift rises the higher you go through the gears.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-261)

  7. Which instrument do you watch if you time your upshifts by road speed?

    • The tachometer
    • The air pressure gauge
    • The speedometer
    Show answer

    Correct answer: The speedometer

    When shifting by road speed, you learn the speeds each gear suits and use the speedometer to tell when to shift up.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-262)

  8. Besides instruments, what can a driver learn to use to know when to shift?

    • The feel of the clutch pedal
    • The sound of the engine
    • The shaking of the steering wheel
    Show answer

    Correct answer: The sound of the engine

    With either the rpm method or the road speed method, a driver can learn to judge shift points by the sound of the engine.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-263)

  9. When shifting down with the basic method, what do you do after releasing the clutch in neutral?

    • Let the engine and gears slow down further
    • Press the accelerator to raise engine speed to the lower gear's rpm
    • Brake hard until the truck slows to the lower gear's speed
    Show answer

    Correct answer: Press the accelerator to raise engine speed to the lower gear's rpm

    For a downshift you raise engine and gear speed with the accelerator to the rpm the lower gear needs before you push in the clutch and shift.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-264)

  10. Which instruments can tell you when to downshift?

    • The tachometer or the air gauge
    • The tachometer or the speedometer
    • The speedometer or the oil gauge
    Show answer

    Correct answer: The tachometer or the speedometer

    Downshifting, like upshifting, can be timed by rpm on the tachometer or by road speed on the speedometer.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-265)

  11. Why must you downshift before going down a hill?

    A tractor-trailer coming down a long, steep mountain road, about to pass a yellow diamond warning sign that shows a truck on a slope.
    • So the brakes do not overheat and lose braking power
    • So the engine uses less fuel on the way down
    • So the tires wear less on the way down
    Show answer

    Correct answer: So the brakes do not overheat and lose braking power

    If you go down a hill too fast in a high gear, you have to brake hard. Hard braking can overheat the brakes so they lose their power.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-266)

  12. Compared with the gear needed to climb a hill, what gear is usually right for going down it?

    A tractor-trailer coming down a long, steep mountain road, about to pass a yellow diamond warning sign that shows a truck on a slope.
    • The same gear
    • A higher gear
    • A lower gear
    Show answer

    Correct answer: A lower gear

    The gear for the descent is usually lower than the gear needed to climb the same hill.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-267)

  13. When should you downshift for a curve?

    The road ahead seen through a truck's windshield: a two-lane rural road that bends sharply to the right, with a yellow diamond curve sign and a 35 MPH plaque on the right before the bend.
    • While you are in the middle of the curve
    • After you come out of the curve
    • Before you enter the curve
    Show answer

    Correct answer: Before you enter the curve

    Slowing down and downshifting early keeps some engine power available in the curve, which keeps the vehicle steadier and lets you accelerate sooner.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-268)

  14. How do you usually control a multi-speed rear axle or an auxiliary transmission?

    • With a selector on the main gearshift lever
    • With a pedal beside the clutch
    • With a lever mounted on the steering column
    Show answer

    Correct answer: With a selector on the main gearshift lever

    These extra-gear units are normally operated from a selector knob or switch found on the main transmission gearshift lever.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-269)

  15. Why would you select a low range on an automatic transmission?

    A tractor-trailer coming down a long, steep mountain road, about to pass a yellow diamond warning sign that shows a truck on a slope.
    • To get greater engine braking on a downgrade
    • To get quicker acceleration on a flat road
    • To stop the transmission from using the governor
    Show answer

    Correct answer: To get greater engine braking on a downgrade

    In a low range the transmission normally will not go above the gear you picked, unless the governor rpm is exceeded, so the engine does more of the braking on a downgrade.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-270)

  16. In a selected low range, when can an automatic transmission still shift up past that gear?

    • When the driver lets off the accelerator
    • When the governor rpm is exceeded
    • When the road becomes level
    Show answer

    Correct answer: When the governor rpm is exceeded

    A low range holds the gear except when the governor rpm is exceeded.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-271)

  17. What benefit do retarders give your service brakes?

    • Less brake wear
    • Shorter stopping distance on dry roads
    • More air pressure in the system
    Show answer

    Correct answer: Less brake wear

    Because a retarder helps slow the vehicle, the service brakes are needed less and wear less.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-272)

  18. Which list names the four basic types of retarders?

    • Exhaust, engine, hydraulic and electric
    • Exhaust, engine, air and mechanical
    • Hydraulic, electric, spring and vacuum
    Show answer

    Correct answer: Exhaust, engine, hydraulic and electric

    The four basic retarder types are exhaust, engine, hydraulic and electric.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-273)

  19. How is a retarder switched on or off?

    • The driver can turn it on or off
    • Only a mechanic can turn it on or off
    • Only the brake pedal can control it
    Show answer

    Correct answer: The driver can turn it on or off

    The driver can turn any retarder on or off, and on some vehicles can also adjust its power.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-274)

  20. When a retarder is turned on, when does it apply its braking power?

    • Whenever the brake pedal is pressed lightly
    • Whenever the accelerator is fully released
    • Whenever the engine goes above its top rpm
    Show answer

    Correct answer: Whenever the accelerator is fully released

    A retarder that is switched on brakes the drive wheels only, and does so each time the accelerator is fully released.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-275)

  21. Which wheels does a retarder apply its braking power to?

    • The steering wheels only
    • The drive wheels only
    • All wheels of the vehicle
    Show answer

    Correct answer: The drive wheels only

    A retarder brakes only the drive wheels, which is why poor traction there can cause a skid.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-276)

  22. Why should a driver learn where retarder use is permitted?

    • Because retarders can be noisy
    • Because retarders can overheat the brakes
    • Because retarders use extra fuel in towns
    Show answer

    Correct answer: Because retarders can be noisy

    Retarders can be noisy, so a driver should know where using them is allowed.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-277)

  23. On which roads should you turn the retarder off?

    • Wet, icy or snow covered roads
    • Steep downhill roads with dry pavement
    • Any road where you are driving slowly
    Show answer

    Correct answer: Wet, icy or snow covered roads

    On slippery roads, poor traction at the drive wheels can let the retarder make them skid, so turn it off.

    Source: ⁨CDL manual, national model as printed by New Jersey, Sections 1 to 3 (July 2017)⁩

    Report a problem with this question (cdl-gk-s2-278)