Driving Test Practice
English

Your stateNot chosenChoose it to see the page numbers of your state's own CDL manual.

Doubles and Triples: Coupling and uncoupling doubles and triples

The steps for coupling and uncoupling twin trailers with a converter dolly, triple trailers, and other combinations. Split into 2 shorter tests so you're not stuck in one long quiz.

Independent educational site · not affiliated with any government agency or DMV

All 40 Coupling and uncoupling doubles and triples questions with answers

Choose a part above to take a practice test, or study every question and answer here.

Show the questions and answersHide the questions
Part 120 questions
  1. The rear trailer has no spring brakes. How do you set its emergency brakes before you couple the dolly to it?

    • Hook up the emergency line, fill the trailer air tank, then unhook the line
    • Hook up the service line, drain the trailer air tank, then leave the line on
    • Hook up the emergency line, drain the air tank, then leave the line hooked up
    Show answer

    Correct answer: Hook up the emergency line, fill the trailer air tank, then unhook the line

    Charging the trailer tank through the emergency line and then removing the line sets the trailer emergency brakes, provided the slack adjusters are set right.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-018)

  2. You are not sure the brakes of the rear trailer will hold it still. What extra step protects you?

    • Lower the landing gear all the way down
    • Open the air tank petcock on the dolly
    • Chock the wheels of that trailer
    Show answer

    Correct answer: Chock the wheels of that trailer

    When you cannot trust the trailer's brakes, wheel chocks keep it from rolling.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-019)

  3. In a set of twin trailers, which trailer gives the safest handling when it is placed right behind the tractor?

    • The trailer that is more lightly loaded
    • The trailer that is more heavily loaded
    • The shorter of the two, whatever its load
    Show answer

    Correct answer: The trailer that is more heavily loaded

    Put the heavier load up front and the lighter trailer at the rear for better stability on the road.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-020)

  4. What is the job of a converter dolly in a set of doubles?

    • It adds a fifth wheel so a second semitrailer can be hitched behind the first
    • It lets the tractor pull the first trailer without using its own fifth wheel
    • It carries the air tank that supplies the tractor's parking brakes
    Show answer

    Correct answer: It adds a fifth wheel so a second semitrailer can be hitched behind the first

    A dolly has one or two axles and its own fifth wheel, so a semitrailer can be hooked behind a tractor-trailer to make a double bottom.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-021)

  5. How do you release the brakes on a converter dolly that has no spring brakes?

    A converter dolly standing alone in a yard, seen from the side: a short steel frame on one axle, a fifth wheel on top, a drawbar ending in a ring at the front with two safety chains, and a support leg under the drawbar.
    • Pull out the trailer air supply knob in the cab
    • Turn the shut-off valve at the dolly's rear
    • Open the petcock on the dolly's air tank
    Show answer

    Correct answer: Open the petcock on the dolly's air tank

    Draining air through the dolly tank petcock frees its brakes. A dolly with spring brakes has a parking brake control instead.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-022)

  6. When you move the dolly by hand to the front of the rear trailer, what should it be lined up with?

    • The landing gear of that trailer
    • The kingpin of that trailer
    • The rear axle of the first trailer
    Show answer

    Correct answer: The kingpin of that trailer

    The dolly must sit squarely in line with the kingpin so it can be backed under the trailer.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-023)

  7. Under what condition may you move the converter dolly into place by hand?

    A converter dolly standing alone in a yard, seen from the side: a short steel frame on one axle, a fifth wheel on top, a drawbar ending in a ring at the front with two safety chains, and a support leg under the drawbar.
    • The dolly's brakes are still applied
    • The distance is not too great
    • The dolly has only one axle
    Show answer

    Correct answer: The distance is not too great

    Hand positioning suits a short distance only; for a longer move the tractor and first semitrailer fetch the dolly.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-024)

  8. You use the tractor and first semitrailer to fetch the dolly. Right after you hitch the dolly to the rear of the first trailer, what comes next?

    • Lower the dolly support
    • Lock the pintle hook
    • Unhook the dolly again
    Show answer

    Correct answer: Lock the pintle hook

    Once the dolly is coupled to the first trailer, the pintle hook is locked before the dolly is moved.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-025)

  9. While you tow the dolly with the first semitrailer to the second trailer, where should the dolly support be?

    • Lowered halfway as a skid guard
    • Resting on the first trailer's bumper
    • Raised and secured
    Show answer

    Correct answer: Raised and secured

    While the dolly is pulled into place behind the first trailer, its support stays secured in the raised position.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-026)

  10. You have pulled the dolly close to the nose of the second semitrailer. Before you unhook it from the first trailer, what must you do?

    • Raise and secure the dolly support
    • Release the dolly's fifth wheel latch
    • Lower the dolly support
    Show answer

    Correct answer: Lower the dolly support

    The dolly support is put down before the dolly is unhooked from the first trailer.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-027)

  11. When you connect the dolly to the front trailer, what do you back into position?

    • The dolly, toward the rear trailer
    • The second trailer, toward the tractor
    • The first semitrailer, in front of the dolly
    Show answer

    Correct answer: The first semitrailer, in front of the dolly

    The first semitrailer is backed until it is directly ahead of the dolly's tongue, ready to be hooked.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-028)

  12. Before you back the dolly under the rear trailer, how must that trailer be held?

    • Brakes locked or wheels chocked
    • Landing gear fully raised
    • Air lines already connected to the dolly
    Show answer

    Correct answer: Brakes locked or wheels chocked

    The rear trailer must not move while the dolly is pushed under it, so its brakes are locked or its wheels chocked.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-029)

  13. How should the height of the rear trailer compare with the dolly's fifth wheel before you back under it?

    • Slightly lower than the fifth wheel center
    • A little higher than the fifth wheel center
    • Exactly level with the fifth wheel center
    Show answer

    Correct answer: Slightly lower than the fifth wheel center

    The trailer must sit slightly lower than the fifth wheel center, so the dolly raises it a little as it is pushed under.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-030)

  14. After the dolly is backed under the rear trailer, why do you lift the trailer's landing gear a little off the ground?

    The landing gear of a coupled trailer seen from the side: its two legs hang about a foot above the pavement, and the crank handle hangs loose from its shaft.
    • To dump air from the trailer brake chambers
    • To avoid gear damage if the trailer moves
    • To test whether the dolly brakes will hold
    Show answer

    Correct answer: To avoid gear damage if the trailer moves

    Lifting the gear slightly keeps it from being damaged should the trailer move.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-031)

  15. How do you test that the dolly is locked onto the rear trailer?

    • Back the dolly harder against the trailer
    • Pull against the trailer's kingpin
    • Raise the landing gear and watch the trailer settle
    Show answer

    Correct answer: Pull against the trailer's kingpin

    Pulling against the kingpin of the second semitrailer shows whether the coupling has really locked.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-032)

  16. When you look over the finished dolly coupling, what should you see between the upper and lower fifth wheel?

    • No space between them
    • A narrow gap for the plates to move
    • Grease filling a small gap
    Show answer

    Correct answer: No space between them

    The plates must sit tight together with the jaws shut on the kingpin; a gap means a bad hookup.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-033)

  17. In the visual check of a finished dolly coupling, what must the locking jaws be doing?

    • Resting open against the kingpin
    • Closed on the kingpin
    • Closed on the dolly's pintle eye
    Show answer

    Correct answer: Closed on the kingpin

    Closed jaws on the kingpin show the dolly is really locked to the trailer.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-034)

  18. After the visual check of the dolly coupling, which connections do you make to the rear trailer?

    • Safety chains, air hoses and landing gear crank
    • Air hoses, light cords and pintle hook release
    • Safety chains, air hoses and light cords
    Show answer

    Correct answer: Safety chains, air hoses and light cords

    Once the coupling looks right, the safety chains, the air hoses and the light cords all get hooked up.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-035)

  19. Which valves do you close at the back of the second trailer, along with the dolly tank petcock?

    • Its service and emergency valves
    • Only its emergency shut-off valve
    • Its landing gear air valves
    Show answer

    Correct answer: Its service and emergency valves

    Both shut-offs at the back of the last trailer are closed, as is the dolly tank petcock.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-036)

  20. Which shut-off valves are opened so air can pass to the dolly and the rear trailer?

    The rear of a trailer that can pull another trailer: two small shut-off valves with lever handles on the air pipes that end in glad hands, and a pintle hook between them.
    • The ones at the rear of the first trailer
    • The ones at the rear of the second trailer
    • The converter dolly air tank petcock
    Show answer

    Correct answer: The ones at the rear of the first trailer

    Air must flow back through the first trailer, so its rear shut-offs, and any on the dolly, are opened.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-037)

Part 220 questions
  1. Once the dolly is attached and the lines are connected, what do you do with the rear trailer's landing gear?

    • Leave it slightly lowered for support
    • Raise it all the way up
    • Lower it until it rests on the ground
    Show answer

    Correct answer: Raise it all the way up

    The landing gear is fully raised before the rig is driven, after the earlier slight lift.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-038)

  2. How do you charge the trailer brakes before checking for air at the back?

    • Pull the trailer hand valve all the way out
    • Open the dolly tank petcock
    • Push the air supply knob in
    Show answer

    Correct answer: Push the air supply knob in

    Pushing the air supply knob in sends air back to the trailers so you can check at the rear.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-039)

  3. You open the emergency line shut-off at the back of the second trailer, but no air comes out. What does that tell you?

    • Only the parking brake is affected
    • The brakes will not work at all
    • The air tank is simply full already
    Show answer

    Correct answer: The brakes will not work at all

    Without air at the rear, the trailer brakes cannot operate, and the problem must be found before driving.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-040)

  4. You are about to uncouple the rear trailer of a set of twin trailers. How should the rig be parked?

    • Straight, on firm and level ground
    • Slightly angled, on a small slope
    • Straight, on soft ground to hold it
    Show answer

    Correct answer: Straight, on firm and level ground

    Before uncoupling, the rig must stand straight on ground that is firm and level, so nothing shifts or sinks while the trailers are separated.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-041)

  5. Once the twin-trailer rig is parked, what do you apply so it cannot move while you uncouple the rear trailer?

    • The service brake pedal
    • The parking brakes
    • The trailer hand valve
    Show answer

    Correct answer: The parking brakes

    You set the parking brakes so the whole rig stays still during the uncoupling work.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-042)

  6. When must you chock the wheels of the second trailer before uncoupling it?

    • When the trailer has no spring brakes
    • When the trailer is loaded heavily
    • When the ground is slightly wet
    Show answer

    Correct answer: When the trailer has no spring brakes

    When the second trailer has no spring brakes, its wheels are chocked before uncoupling.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-043)

  7. Why do you lower the landing gear of the second semitrailer before pulling the dolly out?

    The same gap during uncoupling, seen from the side: the second trailer stands on its lowered landing gear, the dolly is still under its nose and still hitched to the first trailer, and the lines between the dolly and the second trailer are disconnected and hung up.
    • To take some of the load off the dolly
    • To release the dolly's spring brakes
    • To open the dolly's air tank petcock
    Show answer

    Correct answer: To take some of the load off the dolly

    The second semitrailer's landing gear is lowered just enough to take some weight off the dolly.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-044)

  8. Before you disconnect the dolly's air lines, what do you close at the back of the first semitrailer?

    • The air tank drain valves
    • The air shut-offs
    • The glad hand couplers
    Show answer

    Correct answer: The air shut-offs

    The shut-offs at the rear of the first semitrailer (and on the dolly, if it has them) are closed before the dolly's lines are disconnected.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-045)

  9. What should you do with the dolly's air and electric lines when you uncouple the rear trailer?

    The gap between the two trailers of a set of doubles, seen from the side at close range: the ring of the dolly's drawbar sits in the latched pintle hook at the rear of the first trailer, two safety chains hang under the drawbar, air and electrical lines cross the gap, and the nose of the second trailer rests on the dolly's fifth wheel.
    • Keep them connected until the dolly is unhitched
    • Disconnect them and secure them
    • Disconnect only the air lines
    Show answer

    Correct answer: Disconnect them and secure them

    All the dolly's air and electric lines are disconnected and secured.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-046)

  10. Which latch must be released before the dolly can be pulled out from under the rear trailer?

    • The pintle hook on the first semitrailer
    • The converter dolly fifth wheel latch
    • The kingpin lock on the tractor
    Show answer

    Correct answer: The converter dolly fifth wheel latch

    The dolly's own fifth wheel holds the rear trailer's kingpin, so that latch is opened before the dolly leaves.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-047)

  11. How do you move the dolly out from under the rear semitrailer?

    The same gap during uncoupling, seen from the side: the second trailer stands on its lowered landing gear, the dolly is still under its nose and still hitched to the first trailer, and the lines between the dolly and the second trailer are disconnected and hung up.
    • Pull the tractor, first trailer and dolly forward slowly
    • Roll the dolly out by hand at once
    • Pull the tractor, first trailer and dolly forward quickly
    Show answer

    Correct answer: Pull the tractor, first trailer and dolly forward slowly

    With the latch released, the tractor, first semitrailer and dolly are drawn forward slowly until the dolly is clear.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-048)

  12. After the dolly is out from under the rear trailer, what is the first step to uncouple the dolly itself?

    • Release the pintle hook
    • Lower the dolly's landing gear
    • Disconnect the safety chains
    Show answer

    Correct answer: Lower the dolly's landing gear

    The dolly's support legs are lowered first so it will stand on its own once it is free.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-049)

  13. When you uncouple the converter dolly from the first semitrailer, what do you do about the safety chains?

    The gap between the two trailers of a set of doubles, seen from the side at close range: the ring of the dolly's drawbar sits in the latched pintle hook at the rear of the first trailer, two safety chains hang under the drawbar, air and electrical lines cross the gap, and the nose of the second trailer rests on the dolly's fifth wheel.
    • Disconnect them
    • Wrap them around the pintle hook
    • Leave them on until you drive off
    Show answer

    Correct answer: Disconnect them

    The safety chains between the dolly and the first semitrailer are disconnected as part of freeing the dolly.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-050)

  14. How do you keep the dolly from rolling once it is being uncoupled?

    • Set the tractor parking brake only
    • Apply its spring brakes or chocks
    • Raise its landing gear fully
    Show answer

    Correct answer: Apply its spring brakes or chocks

    The dolly has to be held in place, either by its spring brakes or by chocks under its wheels.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-051)

  15. What do you release on the first semitrailer to free the converter dolly from it?

    • The dolly fifth wheel
    • The pintle hook
    • The kingpin
    Show answer

    Correct answer: The pintle hook

    The dolly is hitched to the first semitrailer by its pintle hook, so releasing that hook frees it.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-052)

  16. What can happen if you unlock the pintle hook while the dolly is still under the rear trailer?

    The gap between the two trailers of a set of doubles, seen from the side at close range: the ring of the dolly's drawbar sits in the latched pintle hook at the rear of the first trailer, two safety chains hang under the drawbar, air and electrical lines cross the gap, and the nose of the second trailer rests on the dolly's fifth wheel.
    • The rear trailer's brakes lock up
    • The dolly's air tank loses its pressure
    • The tow bar can fly up and hurt someone
    Show answer

    Correct answer: The tow bar can fly up and hurt someone

    The tow bar may spring up, which can injure someone and also makes it very hard to couple again.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-053)

  17. When you build a triple-trailer rig, how do you couple the tractor to the first trailer?

    • With the usual tractor-semitrailer coupling method
    • With the method for coupling a double bottom
    • With the dolly attached to the tractor first
    Show answer

    Correct answer: With the usual tractor-semitrailer coupling method

    The first step is an ordinary tractor-semitrailer coupling, done the same way as for any single semitrailer.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-054)

  18. After the tractor is coupled to the first trailer of a triples rig, how is the second trailer added?

    • With a second fifth wheel on the first trailer
    • With a dolly, using the method for coupling doubles
    • By backing the tractor under the second trailer
    Show answer

    Correct answer: With a dolly, using the method for coupling doubles

    A converter dolly is moved into place and the first trailer is coupled to the second the same way as in a set of doubles.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-055)

  19. What is done first when you uncouple a triple-trailer rig?

    • The first dolly is lowered to the ground
    • The dolly is pulled out from under the first trailer
    • The third trailer is uncoupled by pulling its dolly out
    Show answer

    Correct answer: The third trailer is uncoupled by pulling its dolly out

    You begin at the back: the dolly is pulled out from the third trailer and then unhitched, as you would for doubles.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-056)

  20. You will drive a truck-trailer combination that is not one of the common types. How do you learn the correct way to couple it?

    • Copy the way another driver couples his rig
    • Follow what the manufacturer or owner specifies
    • Use the steps for the closest common type of rig
    Show answer

    Correct answer: Follow what the manufacturer or owner specifies

    There are too many kinds of combinations for one method, so you learn the correct way from the manufacturer or the owner's specifications.

    Source: ⁨CDL manual, national model as printed by New Jersey, Section 7 (July 2017)⁩

    Report a problem with this question (cdl-dt-s7-057)